Sony Repair Tips
Search: sony
Results: 20072
Results: 20072
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SONY |
HMK339
|
Missing part number | Part designated as spring plate on exploded view page 32 ofs/m has no part number. -hq comments: the part number is 3-554-215-00. | ||
SONY |
HMK339
|
Defective rubber on reel assembly | The take up reel does not take up the tape properly. tapeballs up between capstan and take up reel, and get damaged. this iscaused by lack of pressure between drive pulley and take up reel rubbersurface. | ||
SONY |
HME228
|
Wrong value cap installed | No separation in stereo. all voltages looked ok - factoryerror. | ||
SONY |
HP219A
|
Boards have changed | Manual lists the part number as k-006-048-10, part beingreceived is k-0660-481-0. -hq comments: the servo amplifier and dc motor set has been changed andthe former set is no longer available. the part number of the set(k-066-048-10) remains the same. | ||
SONY |
CFSD7
|
Lever needed bending | Solenoids would click but tape mechanism would not move.lever a would rise over cam gear a causing the mechanism not to bepushed down into gear. | ||
SONY |
CFSD7
|
Link lever binding | Cannot place tape deck in any mode. forward led on all the time. | ||
SONY |
CFS55
|
Defective r308 and switch | B+ section of switch malfunctions either on tape or radio orboth at same time, also affects battery operation. r308 was also open. | ||
SONY |
CFS55
|
Defective lock plate | Buttons jammed up, lock plate too soft. | ||
SONY |
CFS45
|
Belt comes off | Tape would not move in any direction. found belt off motorpulley. | ||
SONY |
CFM31
|
Bridge on pcb | The only function that did not work was am. | ||
SONY |
CFM31
|
Lever breaks | Customer forces record lever down, forcing lever (a) againstlever (b) which breaks or shears lever (a) pivoting stud which is a partof sub-chassis. also this forces ff lever up breaking its guide postwhich is also a part of sub-chassis. | ||
SONY |
CF550
|
Incorrect sub-motor supplied | Original motor (8-834-009-01) requires 3 mounting holes whilesub-motor 8-834-009-10 needs 2. -hq comments: correct sub-motor number is x-354-931-41. | ||
SONY |
CF520
|
Motor will not run | R401 opens. motor will not run. | ||
SONY |
ALL AUD
|
Substitute transistor is incorrect | The substitute transistor for 2sd667, listed as 2sa768 onfisch card and in the computer is wrong. -hq comments: the only substitute is 2sd667a. this has been correctedin the 1988 substitution book. | ||
SONY |
ALL TVP
|
Replacement heads come without mounting screws | Replacement heads come without mounting screws. | ||
SONY |
ALL TVP
|
Servicing is dangerous | The entire inverter power supply is directly connected to theac line. when troubleshooting the power supply circuits, an isolationtransformer must be used. | ||
SONY |
TCK96R
|
Drive slider tab needed to be bent | Door was jammed. cass. transport locked up in play mode,consequently eject mode would not work. found 2 roller pins (p/n 3-558-448-00) had become misaligned. | ||
SONY |
STRV55
|
Defective capacitor | Interstation noise on am and fm. receiver will not scan orselect stations via memory presets. all segments of display tube lit up. | ||
SONY |
STR7800
|
Cleaning/replacing tuning capacitor | Extreme static on fm tuning knob is sensitive. over thephone it sounded like a poor ground (intermittent). the dealer is ina very humid area. | ||
SONY |
PSX40
|
Hall device/offset out of adjustment | After power was applied and start/stop button pressed, turn-table had a washing machine action. |