Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
RD6000
|
Audio distortion, sub ic113/114 per service bulletin 24 | Old version ic113/144 no longer available. need to modify rd6000 audio mcb to allow proper operation of bbd circuit. | ||
| SONY |
XTCF11RDS
|
Ferrari oem model, repair at detroit oem only | |||
| SONY |
XTCF10
|
Ferrari oem courage, repair at detroit oem only | |||
| SONY |
XR7400
|
Part number for cable | Customer has cdx45 unilink type, and xr7400 none unilink.wants to connect two units, has a converter xa18 but needs 13 pins doublemale type cable for connecting two units. please give us part number.y suto 810-347-3370 fax 810-344-4899. -hq comments | ||
| SONY |
XMF10
|
Ferrari oem model, repair at detroit oem only | |||
| SONY |
CDXF10
|
Ferrari oem model, repair at detroit oem only | |||
| SONY |
CDX5070
|
Would not accept discs (found q1 defective) | At power-up, loading motor would run for several seconds, evenwith no disc inserted. when i did insert a disc, the player would notaccept it. i checked action of disc detection photosensor signals ph1 andph2. ph1 was always high. ph2 toggled normally wh | ||
| SONY |
CCDV8AFU
|
Capstan motor will not start in reverse direction / rpl c414 | The capstan motor will not go in reverse mode. found highlevel ripple on audio 5 v lines caused by shorted c414. apparently shouldnot cause capstan propblems. | ||
| SONY |
CCDTR71
|
Intermittent playback video - c303/vs-93 bd | Unit came in with e-e ok but there was no playback video signal.i followed video up through ic151. at ic151 pin#7 signal was good but atpin#3 signal was lost. i then followed signal through some transistors upto q166 and the signal was still good | ||
| SONY |
CCDTR71
|
Rolling black data screen in viewfinder l852/vc112 bd | In camera mode there would be a rolling black datascreen in the viewfinder and no video out. no sync burst or video. | ||
| SONY |
CCDTR70
|
When vc-145 board replaced imager doesn't work/reverse cn701 | Imager stops working after board is replaced. | ||
| SONY |
CCDTR70
|
No chroma camera e to e - l605/vc board | No chroma camera video found that l605 was not passing the chroma signal. | ||
| SONY |
CCDTR70
|
No evf pix / missing data page "d", address b0 to bb | No evf pix. | ||
| SONY |
CCDTR61
|
No power c923/dd-56 bd | Unit came in with no power. i checked the fuses and f902 wasblown. after replacing the fuse and powering it back up it blew anotherfuse. i measured this line to ground which measured a short. i thendisconnected the power supply and then powered up the | ||
| SONY |
CCDTR5
|
No zoom (tele or wide)- q703/ld-11 | Unit came in with no zoom in both directions. there was nooutput to the zoom motor. going back to the zoom motor drive i found theinput ok but no output. taking dc measurements around this ic i foundpin#5 of ic701 low. following this back through | ||
| SONY |
CCDTR5
|
No sync and low luminance in playback - c270/vs-22 bd | Unit came in with low or no luminance and no sync (in playback).following y signal up to ic203 pin#30 signal was bad. i then back-trackedto pin#31 which the signal was good there. then going to q216 signal wasgood at both base and emitter. going eve | ||
| SONY |
CCDTR400
|
No video from io jacks / cab. knocking parts off board vs104 | No video from io jacko on camcorder. | ||
| SONY |
CCDTR30
|
No output video - ic151/vs board | Video was in viewfinder but not outputting to cables however audio was good to outputs solution: no output from pin 38 ic151 on vs bd all inputs were correct the ic was bad | ||
| SONY |
CCDTR101
|
Dead - x922/vc103 bd | |||
| SONY |
CCDTR101
|
Grinding noise recorded on tape- gear assy | This gear had separated from its brass insert on the chassis,producing irregular motion which caused the belt to rub against its teethapprox. once every second. the noise was being picked up by themicrophone and recorded on tape. |