Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
SAVA1
|
Removal of front panels | The s/m indicates the front panel and grille are removeablefor servicing. however two different servicers have called this week,saying the dowel rods are glued in. this makes it difficult to servicethe unit without damage. also applies to s/n 815449. | ||
| SONY |
MDS501
|
After recording unit will erase entire disc - repl ic101,110 | Unit worked fine all measurements were good, but whenrecording it would record informatin on head but after rec unit woulderase entire disc. noticed pre 94 ic's in unit. | ||
| SONY |
MDS302
|
Dead - reset and resoldered ic201 | Unit totally dead. grounded out ic202 on digital board.unit then flashed standby, resoldered ic201, unit worked. | ||
| SONY |
MDS302
|
Extension cables | Are there any extension cables available for this unit totest mechanical assy outside unit? -hq comments: at the time i am writing this, there are no extensioncables available. i will fax tokyo and ask if they will be available inthe near future. | ||
| SONY |
HCDH1200
|
Unit has no power - replaced q791 | Q791 shorted on main board. no display or operation. unitis dead. | ||
| SONY |
HCDC50
|
Part # missing for head lead cable | The part number for the head lead cable is not listed in theservice manual. head cables from the a & b decks plug into the mainboard at connectors cn311 and cn321. -hq comments: we had notified kansas city parts regarding this matter.update 5/25/95: kc | ||
| SONY |
HCDC33
|
Auto rev not working/grinding - align m2's small gear shaft | When manually changing direction or when deck auto reversesthere is a grinding noise and unit stops or tries to play in the samedirection. problem is usually with deck a. small gear located on m2does not completely line up with larger gear causing te | ||
| SONY |
DTC700
|
Door is always in open mode, ic312 failed - replaced ic312 | Ic312 defective, pin 28 ic312 has 4.7v flashing on and offin cycle of 1 second. cassette door open all the time. i hit closebutton it closes after 1 second it opens and stays open. | ||
| SONY |
CDPCX100
|
Mech jams, won't load cd's - replaced chucking cam | Mechanical noise during load cycle, won't load cd's.found broken chucking cam, ref number 134. unit may work several timesthen will jam. | ||
| SONY |
CDPC545
|
Audio loss - x301 defective | Audio loss after approx. 30 seconds to 1 minute of play. | ||
| SONY |
CDPC315
|
At power on sled does not come to home position - repl ic301 | Upon power up the sled did not come to the home position. | ||
| SONY |
CDP2700
|
Static in audio d/a conv not switching on - repl ic901 | Static in audio all the time, no music, no b+ going to thed/a converters which are ic401 and ic501 | ||
| SONY |
XRU880
|
Insufficient qty. of parts in cap. kit (bulletin # car354) | Capacitor kit x-337-022-11 in the service bulletin car 354indicates that a parts kit contains all of the electrolytic capacitors forrepairing the problem. the capacitor kit came with only 1 capacitor. | ||
| SONY |
XRU770
|
Insufficient qty. of parts in cap. kit (bulletin # car354) | Capacitor kit x-337-022-11 in the service bulletin car 354indicates that a parts kit contains all of the electrolytic capacitors forrepairing the problem. the capacitor kit came with only 1 capacitor. | ||
| SONY |
XRU700
|
Part # addition: ic551 (type mm1175xf-t1, p/n 8-759-096-16) | No part # listed for ic551 (interface ic). | ||
| SONY |
XRU500
|
Part # addition: ic551 (type mm1175xf-t1, p/n 8-759-096-16) | No part # listed for ic551 (interface ic). | ||
| SONY |
XR7280
|
Ph-11 and ph12 are both compatible with replacement parts | The beveled corner on ph-11 and 12 is at pin 1 instead of thenormal pin 2. the real pcb layout is also different than in the servicemanual. i could not find replacements for ph-11 and 12. i have a sampleif you need it. | ||
| SONY |
XR43O
|
Mechanical deck-to-main board extension cable required. | Unit will ff & rew but will not play a tape. need sometype of cable from cn401 of main board to cn401 of eq board on tape mech.unit won't operate and can't look at bottom of unit while it's trying toturn. -hq comments: we advised tokyo of the need for | ||
| SONY |
MDXU1
|
No audio from cd or fm, am o.k. (replaced q520, q512, d513) | No audio from disc or fm, am o.k. | ||
| SONY |
MDX400
|
No power (found cold/broken solder on cnp302) | Unit dead. |