☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20082
Make Model Symptom Problem Solution By
SONY CDX5260
Scratching noise when cd starts or stops Units would make a scratching sound when the cd started up orwhen off or eject was pressed.
SONY CDX5080
Disc loading problem, intermittent Won't accept disc. tried loading disc it clamped, thenwaited 20 seconds to eject. after pressing reset, i tried again and itloaded and played ok. i found no abnormal readings onic-501-24, 25, 26, 39, 46, 47. i was unable to duplicate the problemagain
SONY CDX5060
No functions, main board overdissipated at ic302 Unit had no functions. traced problem to ic302, which caused the main board to be over dissipated.
SONY CDX5060
Scratching noise when cd starts or stops Units would make a scratching sound when the cd started up orwhen off or eject was pressed.
SONY CDX5040
Won't play disc when cold Won't read disc when cold. all ok when it is not cold.replaced pickup but no change. i noticed this problem is addressed in thesonam technical activity report (4/92). has a solution been found? -hq comments: the specific problem mentioned in the acti
SONY NP60D
Cam(ccdfx420) goes into battery down - but batt shows charge Customer complained that his ccdfx420 would go into batteryshutdown, even though the np60d showed that some charge was left. we foundthat the battery still lights one led even at 5.6v, which is just aroundthe battery shutdown voltage on the camera. this
SONY CCDVX3
Intermittent snow in pix/replace fp522 Unit had intermittent picture. took shield off head amp(desoldered). scoped ch 1 and 2 rf. found no output ch 1. touched inputat chip with dental pick and found ch 1 amp and channel 2 working. touchedinput with drum unplugged and found ch1 dead.
SONY CCDV99
No color recorded/l603 (vi-55) open No color recorded on tape by this unit. playback good of othertapes.
SONY CCDV701
Unit will not load 20 min cassettes/check drum base During the loading process, 120 minute cassettes will load andplay normally (all other vtr functions work normally also). but when a 20minute cassette is inserted, the drum motor spins, take-up occurs, and theguides move in the load direction almost com
SONY CCDV101
Japanese characters for month on osd, lcd display ok Due to water damage, we had to replace the ss99 board on thisunit. after installation, we could not get the osd to display the datecorrectly. either it was yy/mm/dd or mm/dd/yy, but with the month injapanese characters.
SONY CCDTR91
Digital solarization , ic604 This camera had distortion that could be described as digitalsolarization. the picture was fine after heating a/d converter.
SONY CCDTR71
No zoom, stuck in manual focus all the time no manual exposure Zoom did not work, auto focus did not work(stuck in manualfocus). no manual operation of exposure and program.
SONY CCDTR61
Loud buzz in camera audio/replace mic unit Loud buzz in camera mode. audio playback of pre-recorded tapeis ok. but any tape recorded on this unit has a loud buzz recorded ontape. this buzz is also evident in e-e. have subsituted good board forau150 and ma170 with no change. please help.
SONY CCDTR505
Blows fuse/check soldering on ic903 Intermittently will blow 1.6a main fuse. when it went badwould draw 1.5a in camera mode.
SONY CCDTR5
Replacement part won't mount/screw too short Receive sub replacement a7040209k, and the assembly isthicker at the mounting where the fixing boss is attached(s/b cam 171).making the original screw too short. use a 1.4 x 3.0(7-627-551-57) screwinstead of the 1.4 x 2.5 screw. -hq comments: this has
SONY CCDTR5
P/n for evf lower cabinet not in service manual The above part isn't in the service manual and i can't find aservice bulletin on this.
SONY CCDTR21
No audio/check l160 No audio was caused by bad solder on one side of l160.re-soldering corrected the problem. -hq comments: l160 passes pb 5v.
SONY CCDTR200
No mechnical motion/replace ic201 This unit came in in the unloaded position and would not load. ic903 was on and there was activity on pins 74, 75, 76 and 77. theselines were also active at ic201 but, x201 was not oscillating.
SONY CCDTR101
Int no video in pb or int b/w of rec images, check q414. Int. b/w and no video of rec. material for this cam. also,int no video of pb pre-rec material. traced signal (y comb out) to q414,which had no signal on emitter (int) checked d.c. voltages around q414 anddetermined trans to be defective.
SONY CCDTR101
Camera e to e output mosaic/download good evr data Both cameras were outputing a mosaic picture e to e. core icwas replaced and vc103 board without solving the problem.