Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
WMA602
|
Poor solder connection at battery terminal | The negative battery terminal on this model often has a poorsolder connection. | ||
| SONY |
WMAF604
|
Poor solder connection on battery terminal | The negative battery terminal on this model often has a poorsolder connection. | ||
| SONY |
WMF2085
|
No p/n for belt clip listed in s/m | The p/n for the belt clip supplied with the unit is not listedin the service manual. | ||
| SONY |
CFD444
|
Service manual error - voltage on q-711 | One of our servicers detected an error in the service manual.while troubleshooting the unit, he measured 3.7 vdc at the emitter ofq-711. the manual has it listed as 7 vdc. -hq comments: you are correct. thank you for pointing this out to us.the manual | ||
| SONY |
CDP101
|
Door won't open/grease hardened | Door won't open. lever 165 (page 66) won't go back to restingposition which allows door to open. there is a spring on this lever whichis to pull it back into resting position. the problem is the grease thatis on the shaft has hardened and turned to gl | ||
| SONY |
CCDV99
|
No video playback of hi-8 metal e tapes | No video in playback mode with use of hi-8 metal e tapes.only a gray screen with audio. | ||
| SONY |
CCDTR7
|
No zoom | Zoom block assembly was frozen. took apart and tried to freeup, but to no avail (part not supplied). | ||
| SONY |
KPR46CX10
|
Snow when connected with cable converter, replaced cable box | When connected as shown in owners manual, with cable converterthe picture will be snowy. also tested kv-27xbr10 on same location andproblem did not show. -hq comments: found that the customers cable box was not puttingout the signal at channel 3 freque | ||
| SONY |
XM601
|
No output | No output because of no power. | ||
| SONY |
CCDM8U
|
Unit will not load- power led flashes | Unit will not load or unload. | ||
| SONY |
SL810D
|
No part number for lower drum assembly | Part number is not given for lower drum entire assembly notavailable. | ||
| SONY |
MDP333
|
No operation | No display/spindle motor spinning counter-clockwise. alsoapplies to serial number 816851. | ||
| SONY |
CCDM8U
|
No camera video iris is ok | Unit had no record y signal. signal out of pin 15 of the ed11(rec y) was not there. tried to inject video from a generator and founded-11 board shorting out signal. lifted pin 15 of the ed-11 board toconfirm the problem. | ||
| SONY |
KV27AVR
|
No audio, replace d-601 | No output from any audio input. display showed volume controlbut no balance control. found d-601 shorted putting 15v on pin 23 ofic-601. | ||
| SONY |
HVM200
|
Blown fuse f-101 | Blown power supply fuse. apparent confusion over what powersupply is required. no specific sony supply specified in manual. note -error on front page of service manual under power consumption. also,page 5 of service manual, item 13, connect the land | ||
| SONY |
CDXR79
|
Cd skips and freezes up on certain tracks | Cd plays beginning of the first track and then freezesup at the middle and the end of the cd. | ||
| SONY |
CDXR77
|
Cd skips and freezes up on certain tracks | Cd plays the beginning of certain tracks and then freezes upin the middle and the end of the cd. | ||
| SONY |
CDXR79
|
Unit skips when car hits bumps | Unit is too sensitive to shock. it skips when car hits aslight bump. | ||
| SONY |
CFSDW80
|
Incorrect part number s-906 - deck a | Please refer to supplement 1, exploded view on page 2. aswitch different than the one indicated as s906 is received when partnumber 15713321 is ordered (this is the part number shown in the mainservice manual for s906). can you please supply this numbe | ||
| SONY |
TCH500
|
Power cable part number | What is the part number for the cable used to power this unit? -hq comments: the part number can be found in the mhc-5500 servicemanual. it is listed under connecting cord and the part number is1-575-667-11. |