Sony Repair Tips
Search: sony
Results: 20100
Results: 20100
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SONY |
CDP620ES
|
Will not read toc - noisy focus search | Unit seemed to have a focus servo or search problem. withscope on fo test point, focus search going up was ok but in focus searchgoing down there seemed to be an open servo loop. | ||
| SONY |
CCDM8U
|
Need part number for chassis on page 126 | Need part number for chassis on page 126. -hq comments: the part number is a-7010-080-a. a s/b will be issued. | ||
| SONY |
TCFX510R
|
Incorrect description in s/m | Correct p/n for case, silver should be 3-307-532-31 and forblack one should be 3-307-532-11. -hq comments: we will issue a service bulletin. | ||
| SONY |
SDP505ES
|
Wrong part number | Ic702 (cxp5016h-118s p/n 8-759-800-54) was ordered from kcp.received p/n 8-759-800-54 (an la3365 ic). la3365 is correct. micro-processor has incorrect part number. | ||
| SONY |
FD3A
|
Dial pointer, x-3332-204-1 | Pointer missing from unit. pointer is not declared onexploded views in fd-3a or fd-2a manuals. | ||
| SONY |
KV2080R
|
Pop in sound, value changes | With external amplifier/speaker pop in sound when changingchannels. -hq comments: to fix the problem make the following component changes:c1461, c1462 from 1u/50v to 4.7u/50v (p/n 1-124-192-00)r1461, r1464 from 22kΩ to 1kΩ/1/6w (p/n 1-247-831-00). | ||
| SONY |
CDXR7
|
Pll free run frequency adjustment | To adjust pll free run - l501. | ||
| SONY |
STRAV580
|
No memory | No memory of stations. | ||
| SONY |
EVS700U
|
Intermittent noise during pcm playback (tracks 4, 5, 6) | 1) pcm playback of tracks 4, 5, 6 has dropout during audioplayback. 2) stereo indicator light flashes. 3) video playback has noiseat bottom of screen. | ||
| SONY |
STRVX350
|
No audio output | The speaker relay would not engage although the audio outputsand sensing circuits were ok. | ||
| SONY |
CCDM8U
|
Drum rotation is erratic and unit shuts down | Drum is erratic and unit shuts down. -hq comments: check c246, md-10 board. we have reports on this capbeing leaky. please inform results. | ||
| SONY |
CCDV3
|
No eject | No eject. unit had been dropped and case was damaged. | ||
| SONY |
XR33
|
No part number for s903 - muting sw | No part number listed for s903 (muting switch). | ||
| SONY |
D5
|
No operation of the unit | The converters +5 volt output fails because of an intermittentshort between the two wires leading to the laser power switch (s901).inspection of these wires may not yield any obvious insulation breakseven though you can measure a short when pulling on th | ||
| SONY |
KV2792R
|
Light picture, no ch would tune in, replace r-1576 | The unit would turn on, but had a light picture washed out.could not tune in any channels. video could be received but light pix. | ||
| SONY |
SLHF300
|
Need part # - right lock base | Can you provide me with the part number for the circledlever? -hq comments: part number is 3-684-232-02 which is called lock (right)base and is available at kcp. | ||
| SONY |
KP5000
|
Overall green tint on upper 1/3rd of projection screen | The upper 1/3 of the screen has an overall green tint to thepicture/program material. i have also seen 2 other kp-5000 projectionsystems recently with the identical problem. -hq comments: please clean crt surface. it will be necessary to removelens as | ||
| SONY |
LCV
|
No part numbers for camera case parts | Customers need parts for various camera. -hq comments: plealse contact me directly if you need any specificparts. we can get them through sales or tokyo. during our internationalserviceability meeting in tokyo, we will suggest making these partsavaila | ||
| SONY |
SLHF1000
|
Flagging during playback in special effects mode (bis) | Picture flags during special effect playback in beta is mode.is this normal? -hq comments: i checked our lab unit and there is no evidence of anyflagging. please try adjusting tape path and inform results. | ||
| SONY |
RM717
|
No channel 3 function | The conductive coating on the ch. 3 pad is worn off and thisfunction will not work. the remote works on all functions except thech. 3 button. bulletin should be produced on disassembly procedured onremotes and the fix for this problem. |