Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY KV2645R
Sound distortion Two transformers were replaced the same week on two different units for excessive vibrations or singing. wedging did not help.
SONY KV2643R
No tuning, replaced c519 No programming any channels on manual or auto. you could setthe stations appear on the screen but they would not be programmed in thememory. during auto program, the neons would not light up in sequence asthe set tuned through the bands, only channel 2
SONY KV2602
Intermittent shut down, replaced cracked hvr block This unit would intermittently shut down. the hvr block had acrack across the bottom.
SONY KV1947R
No tuning most channels, resistor change Kv-2649r will not tune most channels, only 5 and 6. kv-2647rwill tune some of them, some sets will and some of same model will not.
SONY KV1945RS
Dead, d603g Set will not turn on.
SONY KV1941R
Dead, replaced open r812 This tv was dead when servicer received it. replacing thegcs, q901, f602 and t801 restored both picture and sound. however, therewas severe ringing on the left side of raster. all sweep derived voltageslooked clean on scope. further troubleshooting r
SONY KV1922
No color No color, found no 3.58mhz output at cx172. traced problemto capacitor c330 (leaky, reading 300Ω).
SONY KV1730R
Dead This unit lost all signal at the 3rd stage of the remotepre-amp. we found the capacitor in the tank circuit off the collector ofq1103 to be shorted.
SONY KV1546R
Intermittent no color, replaced l304 This unit was losing color intermittently. servicer reportshe has had 2 other units with the same problem.
SONY KV1511
Darker picture on the left side of the screen This unit had a darker picture on the left side of the screen.the screen was divided almost down the middle with the right side normal.scoping the 110v line revealed about 35vpp of horiz. noise c528 was foundto be defective.
SONY KV1222R
Hum noise in the set End user stated he could hear hum coming from the unit evenwhen the unit was turned off. turned out that customer was hearing anarcing within the capacitor. cap is across the ac line in (c601, 0.22uf).
SONY KV1222R
The door will not stay shut The door will not stay shut. -hq comments: the countermeasure to the above problem is given in thedecember 1982 fpr summary.
SONY KP7225
Unable blue horizontal convergence, replaced q5353 Blue horizontal convergence control inoperative.
SONY KP5040
Vertical line in the center of the screen Vertical line in the center of the screen from cross hatchgenerator. lifted resistor's r3393 and r3384 and connected them to ba-9pin 2. this method of getting rd of the vertical line is better thanjumping a capacitor across d3312. with the capacitor a
SONY KP5000
Convergence change, replaced green crt When setting unit up for convergence by placing hatch patternon screen, the set would set up nicely. then when switching the crosshatch off, the pix looked severely mis-converged. closer inspectionrevealed that only the green was mis-converged and in v
SONY TV520
No picture No video when replacement crt is used. have had 5 reports ofthis problem. p/n 8-731-105-15, ct-450 is being subbed by 1-546-039-00.this replacement has an adapter socket to use. however, when hooked upno video is received. -hq comments: installing th
SONY TV115
Intermittent agc This unit displayed very intermittent agc. under very strongsignal conditions it would play well. we found r333 to be thermallysensitive. it looked fine however, no signs of overheating.
SONY KX2501
Dead, replaced d1206 Dead. evp-1 ckt ok, shutting down pps. replaced open r675,produced raster. hooked up a vtx-1000r unit smoked and went dead. r675open again, q1343 open, r02 burned. replaced all parts.
SONY KX2501
No power, replaced t652 This unit had no drive to the converter output on ga board.we found the primary of t652 to be open.
SONY KV9000U
Incorrect parts compatibility Servicer ordered thyristor from distributor using p/n1-801-010. this number subs over on the microfiche to p/n 8-719-000-10.in the semiconductor replacement handbook, page 321, diagram #d040 showsthe lead configuration of the substitute part. if this c