Toshiba Repair Tips

Search: toshiba
Results: 5617

Make	Model	Symptom	Problem	Solution	By
TOSHIBA	48L3663DG	Doesn't start. defective inoperative power supply.	Checking the voltages at the power supply, one of the diodes is shorted. shorted fdd399n15 mosfet	Replace mosfet fdd399n15 = fdpf390n15a and the 56µf capacitor on the line	Vital
TOSHIBA	32W2333D	Doesn't start	Ci u15(5432)	Replace ci	ERP-ASSIST
SEMP TOSHIBA	32RV800	Turns on green LED lights up, backlight doesn't turn on without image, doesn't respond or turns off, sometimes it turns on normally.	Corrupted u702 flash memory.	U702 memory flash (https://www.4shared.com/rar/unvxqp2hce/32rv800_a_da_cmo_atual.html)	EduSSantoz
TOSHIBA	LC3246WDA KK	TV turns off by itself, press power to turn it on again	Power supply board	Replace integrated circuit wn901 (qo765r 0 and c909- 47/50v and c905 47/25v	SANTOMEL
SEMP TOSHIBA	LE3278 I(A)	Lower LED voltage	Remover rp53
SEMP TOSHIBA	LC3246WDA	Turns on and off, backlight flashes, backlight defect, image turns on and off.	Defective lamp connector, oxidized, defective lamp connector, burnt connector	Remove screen to repair	Maike Eletronica Sorriso
TOSHIBA	DL4077L	TV just blinks green LED. blinking and it won't go.	I replaced the LED strip (which was burnt out) and the problem persists.	I replaced dp9 diode. and just ran for a hug. /
SEMP TOSHIBA	1450 U17	Vertical closed	Q422 voltages low, resistor r885 open.	Replace with a 1Ω resistor for 2w.	Tiago C. Neves
SEMP TOSHIBA	TV 2086 LMS U16	Em stand by	Cause r 432 2k7 open	Replaced the resistor r432	ZEZINHO DA ELETRONICA
SEMP TOSHIBA	LE4053(A)DA	Using the philco ph42m led a4 board on the semp toshiba le4053(a)	First, if the image is bad, when they put the philco plate on the semp, go to the semp tec information 012/12 and tsound you have it, depending on the display manufacturer, you type 062598 menu code, depending on the display you type the corresponding code	After that's done, the TV will turn on with a normal image, just write philco and accept it using the remote philco just... to turn it back on, download the semp update and update it with the pen drive... done that, the tv is ready always again.	MIGUELTV
SEMP TOSHIBA	40L2400	LED burnout decrease LED current	Replace r765 behind the board near the LED connector with 4r7	Replaced never come back	Eletrônica alternativa mijail
TOSHIBA	40RV700FDA	Does not even turn on standby...voltages of 5v and 3v normal	On the main board tsound are 3 10uf smd capacitors...c9202, 9203, 9204...one of them was shorted.	Looking at the oscilloscope, you could see that the 3v voltage had a little ripple and kept varying.	GR Eletrônica
SEMP TOSHIBA STI	LE4056(B)F 35016957	Does not turn on, inoperative, does not light stand by LED	Pwm defeito ci 6755 ref-nw907	Replace for another of the same!	Maike Eletronica Sorriso-MT
TOSHIBA	48L2400	The Toshiba logo appears and then the image disappears	Main board goes into backlight protection. If the adaptation of placing a 10k or 15k resistor in place of the r766 does not work, you can perform another procedure to remove the backlight protection.	Place a 10k resistor from pin 41 of the ci oz9916 (ci backlight) to ground.	Dennys Gross
TOSHIBA	42XV650DA	Engages the relay and goes into protection flashing 3 times	Inverter mosfet, check all		Jair
SEMP TOSHIBA	DL3271 (B) W	LEDs would light up and then go out, LED supply voltage would drop from 72v to 25v. LED bars changed and it didn't solve the problem	Resistor rp 70 ao lado do icp4 oz9967gn. resistor smd numeral 105	Opening resistor replaced by another 1m	Thiago Campelo
SEMP TOSHIBA TCL	LE3274	Service mode	Input 3195	Input 3195	Diego Boeira
TOSHIBA	TV 2977(A) SL91	Low sound	Capacitors c636 c637: like low capacitance		Manel Batista Pereira
TOSHIBA	40L5400	Doesn't start. standby off.	Ci n806 ,(fr9889)dc/cd , no output voltage on pin 3.	Ci replace. Thank you for the tip posted by assolini br.	Marotta
TOSHIBA	52XV600	Doesn't start	1.8r open resistor	Replacing the resistor	José