Toshiba Repair Tips

Search: toshiba
Results: 5617

Make	Model	Symptom	Problem	Solution	By
TOSHIBA	2999 LM8	Turns on, when it turns off it no longer works.	Changed power supply	Replace the c819, 47/50 with a 100/50	soyti
TOSHIBA	TV2177 (A) SL	Intermittent power supply, stop	This TV came to me with the horizontal output shorted, after changing it it didn't work after checking the power supply I identified that the tl431 was open after changing it the TV started to discharge and cut out, I identified the r851 fir and the TV started working normally again.	R 851 220k e la76 431, tl431	FERNANDO
TOSHIBA	TV 2916 LEM9	Low power supply with + - 80 v and pulsing	878 resistor altered from 34k to 49k	Replace resistor	DEBIQUE
TOSHIBA	TV2134SL SK 11	+b voltage changed from 114v to 152v	C 634 (47x160)dry generating noise	I replaced the c634 and c311 and everything was ok.	digitec eletronica by lambarí d'oeste-mt
TOSHIBA	1482BAV U8	Turns on, turns on stand by but does not oscillate	Solution: change tsh q 404 (bu 2506dx)		BARRETO CRUZ
TOSHIBA	1482BAV U8	Horizontal closing right side of the screen	Solution: replace capacitor 442 (5n6/3/1k6)		BARRETO CRUZ
TOSHIBA	2916 3400	Red with retrace line after working a lot on the board I discovered that the tube was shorted in the red position	Tube replacement		INOCENCIO
TOSHIBA	TV 2134	Extreme width, shrunken vertical and high average 160v power supply	See r851 changed correct value 220k		Master Eletronica
TOSHIBA	2134 SK11	This one had a stand by light but it didn't oscillate as if it were the flay back. It tried to leave, but it set up protection.	After racking my brains I found the c634 completely sold out.	Replace c634	chines eletronica
TOSHIBA	2079FMS	Before leaking on the flyb. blue screen, it doesn't work at all.	Release or replace d901.on the kinescope plate.		JN ELET. NEVES CE
TOSHIBA	TV2050 MAV U17	Dark image	C902 on defective kinescope board		Jaison
TOSHIBA	TV 2095JM	TV turns on normally. then tsound is a blue screen.	Release smd transistor on the kinescope q906 board.		JN ELET. NEVES CE
TOSHIBA	TV 2076BMU	No subtitles, TV works normally.	Res. of 100k open near the fly back.		JN ELET. NEVES CE
TOSHIBA	2090 U14	Does not turn on dead power supply and str 5753 burst.	The str itself is shorted r876 smd of 220 r open d876 of 5v6 shorted and c864 swollen	After replacing all the components mentioned, the TV worked perfectly. Let's post more tips guys.	This email address is being protected from spambots. You need JavaScript enabled to view it.
TOSHIBA	TV2959JFS LEM10	Burning horizontal outlet and not opening vertical	D440 e d408	D440 measures normal but with very high frequency burning at sh and the d408 even measuring well did not rectify the 12v supply to the vertical oscillator..solution to replace both without testing	palauro
TOSHIBA	1480 U13	It works with a loud hiss on power supply m, the screen flashes and the str-g5653a heats up abnormally	R876 changed its value is 680Ω and it was giving 8k2.	Just replace r-876 = 680Ω	samuel leite
TOSHIBA	TV2091 U14	Stop. not even the LED lights up	Capacitor seco e vertical	Replace capacitor c887 100mf/16v, replace ci q301 stv9302a	lider eletronica
TV-TOSHIBA	TV-2916NMS	It turns on normally, but the screen is closed on both sides horizontally and the wid function does not adjust in service mode.	The memory and width capacitors were changed, but it didn't solve the problem and the qd01 and qd02 were shorted and the width went back to normal.		Adilson(formiga- mg)
TOSHIBA	TV2090 U14 U13	Standby	Transistor bu808dfi	Replace with bu508dfi replace transistor 2sc1815 capacitor 47x35 buster capacitor 8n2	cico
TOSHIBA	TV2090I U14	Vertical function worked normally because at some point it would close and sometimes it would come back and hold	After changing everything from the vertical, I had the same problem, after changing the 7805 regulator and 10x35 capacitor, everything was ok.	Replace the regulator and 10mf electrolytic capacitor together and then do the reset	cico ibimirim pe