Toshiba Repair Tips
Search: toshiba
Results: 5617
Results: 5617
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
TOSHIBA |
2095KM
U15 |
TV arrived at the workshop with the 808dfi burnt out, and when changing it and doing all the usual procedures when turning on the TV, it got very hot and the horizontal panel wouldn't open completely. | First of all, dear colleagues, when changing this bu it is essential to detect the cause of the burning, because if you are not going to spend money on the bu for it lol. First of all, change the c419 47mf x 50v, check the 403, I advise you to change it without testing and the q406 which is a c1815 check the q 430 if it is very hot go to the diode d448 and the d449 and immerse its cathode it has to give 11 to 12 volts if 9 volts change them too without testing, the factory code for you to find it at the authorized eo stock code is 457320. particularly I have been using the good old 4f1/10 or by96 in both positions and it hasn't given any feedback lol | In my case, the TV did not open the horizontal completely because the counterfeit bu rerer, be very careful with them, do this, you measure it from pin 1 to pin 3 with the test scale on the original diode measuring scale, give around 200 at 260Ω and the sickle has a maximum of 50Ω, pay close attention to these tips, any questions my number 33 30842033 I'm from Governador Valadares Minas Gerais | |
TOSHIBA |
MS 6531
|
Tsound is a signal in the preamp but tsound is no sound | Q802 do mute ou q803 do st-bay ass e.a | ELETRONICA ARNI-LEOBERTO LEAL-SC | |
TOSHIBA |
TV2088
U14 |
Replace it and check the 113 volts | C877 smd shorted | Replace it and check the 113 volts | DTECH/Djalma de Oliveira |
TOSHIBA |
1495
KMU15 |
Mixed colors | Bobinas ou no | joao | |
TOSHIBA |
TV2157 BFS
FS2A LEM7 |
Vertical closed and tsound was no vertical exit | Tsound were 2 broken lines at the foot of the varicap | Weld | Eletroclaudio Aguas Belas PE |
TOSHIBA |
TV2157 BFS FS2A
LEM7 |
Image with different color half green | R230 smd of 220r on the foot, from micro | Replace | Eletroclaudio Aguas Belas PE |
TOSHIBA |
2086MMS
U17 |
Horizontal outlet heating up and burning | It was the fake j6806d horizontal output, I put the d2624 in and it was ok. | Eletroclaudio Aguas Belas PE | |
TOSHIBA |
TV2916
|
Horizontal outlet burnt or burning | Changing the c 416 - always change it when changing the sh | Master Eletronica | |
TOSHIBA |
TV2157
|
Screen with only blue blurring | Change q906 smd of kinescope board | Master Eletronica | |
TOSHIBA |
TV2084
U13 |
This TV had no sound + it doesn't generate high voltage and it lit the filament | Check the horizontal output note: test on the 1x scale | Roberto | |
TOSHIBA |
TV2050MAV
U17 |
Fica so em stand bay | Check the horizontal output note: test on the 1x scale | Roberto | |
TOSHIBA |
TV205MAV
U17 |
It just stays in stand bay and doesn't generate | Check the horizontal output note: test on the 1x scale | Roberto | |
TOSHIBA |
2056M
U6 |
Black stripe on the left side of the trc. | Dz 302 short, sandcastle pulse. changed, the TV returned to normal. (resolved) | lucas40 | |
TOSHIBA |
2998
|
Turns on normally, after a few minutes a blue pattern starts on the screen like interference, it can even lead to a complete blue screen | Kinescope board diode 1n 4148 | ||
TOSHIBA |
2112DN
|
Doesn't start | Tda4601 shorted and disconnected pin 36 ica01 (cxp80420) | ||
SEMP TOSHIBA |
TV2083BAV
U10 |
Off when volume increases power supply oscillating | Dido zener d876 de 5, shv e p876 smd alterado | Replace | Eletroclaudio Aguas Belas PE |
TOSHIBA |
TV 2977 TV2177
|
Burning of the horizontal outlet | R 851 220k changed making power supply change | Replace it | CARLOS |
TOSHIBA |
TV2015
U17 |
Just hissing sound without video and filament doesn't light up | Change without testing q404 | JOSIMAR | |
TOSHIBA |
TV 2987
... |
TV turns on and off (vertical closed) | R327 aberto | Replace r327 and vertical capacitors | lord |
SEMP TOSHIBA |
TV2050 -TODOS
|
Low hoarse sound, on some devices the image expands into greenish tones | Q906 no gain (polarized) | Replace q906 a smd on the kinescope board (tube) | WAGGUINHO |