☰

Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search:
Results: 88090
Make Model Symptom Problem Solution By
CCE STILE D42
Stops working with the pinkish drizzle screen, noise in the audio.3.3v low. C156 100mf with leak on the u3 side E cobra
GRADIENTE GBT-2011
PCI 605 REV.C 		It doesn't work, it seems to be the horizontal output is shorted, it makes a characteristic horizontal meow C908 C908 102nf 400v Eudes
CCE STILE D42
To work with the pinkish drizzle screen, 3.3v low. C156 with leak on the u3 side E cobra
TOSHIBA 29PT4635/78
It turned on and after about 5 seconds it turned off Defective tube Replace image tube with a good one and just run for the hug. Eletronica Adão
PANASONIC TC 29KL04
Horizontal closed with white line in the middle of the screen C 563 / 394j = 390nf Replace Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821
LG CP-20K42
No image normal sound increases screen nothing appears Diodos 501 e 403 em cuto Replace them and run for the hug
TOSHIBA 32L2400
Normal device works for approximately one minute and turns off. 3.3v regulators Replace without measuring, n805 and n808 3.3v regulators Gabriel GXP
PHILCO PH21 M2 TUBO
When plugging the TV into the socket, the LED lights up, and immediately turns off, and nothing turns on. tensions in the secondary of the choper, in the absence of tension in the horizontal Voltage up to c568 (47/160). cause, r470 of 3w 1.2r or 1r2 open. it did not provide +b for pin 4 of the fly. With the replacement, it worked. Resistor difficult to find, you won't find it in every Philco chassis. Marcos Lizzi, Confresa, MT
SONY MHC-GTR888 HCD-GRT888
Totally off. Power supply without standby, 8v2 voltage is missing, the board says 13v. solution: change all couplers. Naldo Lima
SEMP TV2177(A)SL
SL11 		The TV had no AV image, normal sound Dz 704 short Replace it for another like it ELETRONICA CAVALCANTE EM MARTINOPOLE CEARA
SAMSUNG UE40F6200AK BN44-00616A
Doesn't work, qp801s burnt out Fp801s(5a), qp801cs(13nm60c), rp811(0,47ω), rp810(100ω), rp813(20ω), dp801(bav70t), icp801(sem3050), dp808c(sf38g), cp812(22µf/50v) Andrew
CCE HPS 2007
This TV arrived sound at electronics with the stand bay ledy on when pressing the power key, the ledy just blinks intermittently and the TV doesn't go to the armpit! T401 The T401 had one of the wires broken, I soldered the wire and turned the TV on, forced it to the oxilor and the bu4508dx horizontal output broke. I replaced the t401 and put the new bu4508dx and that's it, the TV worked normally, the t401 was replaced! Sinailson furtado
CCE HPS2991SFC
Turns on oscillates, lights up tube filament and then goes out and relay doesn't work, change the two bc337 transistors and the Vila TV works normally, I hope someone helps you, my colleague. The two bc337 in the horizontal circuit One was open, replace the transistors Sammael Kuznetsov
SEMP TV1453 (P)AV
IMPORTADA 		I'm sound Capacitor c603 470uf 25v Replace without measuring Eletroclaudiope
LG 50PB650B
TV with the HDMI connector ripped out, TV won't come out of standby Mosfet with code mp1 without numbering on the board, it is close to ic603. It's the only one with this code, short. Replace mosfet with the same code and check the hdmi connector tracks and resolder it Ev antunes
CCE TVS 2910FS
Defect Rainbows Burning fr423 Maciel porto
SAMSUNG CL21K40MQ
KS9C 		Turn on is to turn off quickly with a very loud chirp on the flyback Shortened deflector all black inside I put another good one it was good again Algustinho eletrônico
SAMSUNG CL-21Z43MQ
Turns on with sound and no image, low power supply. Tl431 regulator Pardal - X
PHILIPS FX30X
HC11 		Does not turn on, only LED is on D12 on main board I put an in4148 in its place Paulo
PHILCO TP14U56
55 02 F6949 06 2 		Without image, with osd and sound Replace of zd701 20v and r723 10k Eudes