Repair Tips
Search:
Results: 87942
Results: 87942
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
SEMP |
LC3245
|
No audio or failing | Dc dc regulator | This TV arrived with audio faults and finally left | Walter Júnior |
SAMSUNG |
UN40F5500AG
|
Does not turn on, just flashing standby (no backlight) | Without 13v power supply changed 10r resistor was measuring 4.22k next to the pfc capacitor | Replaced capacitor 10r fiz um video video... | Jean Vinicius Franco Lorenz |
SAMSUNG |
UN50TU7000G
|
Backlight off | Poor contact in the power supply board connector, | A direct connection was made from the power supply connector with wire to the LED bar connector, everything was fine | Fernando técnico |
AIWA |
AWS-TV-55-BL-01
|
No image | Defect in the LED bars = 3 bars with 11 3V LEDs each measuring 105.8 cm long | I didn't find it in Brazil, I had to import a model equivalent to the Philco TV model PTV55G20 and PTV55G20AGS other codes LED strip lamp for Skyworth, 55suc6500, th-55hx560c, 55d11-zc62ag-04d, sw55d11-zc62ag-02, 5800-w55g22-0p00, 55d3b11cx106012 | You tube - Direto no defeito |
LG |
26LH20R-LA/TA
LP91A |
Normal image but no sound on all inputs. | 1.8v supply filtering | Changing the 3 smd capacitors next to the audio output c600, c604 and c610 | André Paz |
SDMC |
SDMC DV2712
SDMC DV2712 |
Sdmc dv2712 eeprom data for download | Sdmc dv2712 eeprom data | Dados eeprom receptor sdmc dv2712 external link... | NEUPSX4 |
PANASONIC |
TC14RM15L
|
Turning off | R 850 de 56 r 3w | Swap 850 56r 3w | Raimundo tec |
LG |
50PN4500
|
Stand by lights up but tv doesn't turn on | All voltages ok, standby turns on, TV doesn't turn on, | Transitor q604 (x7ua) with problem, replaced and resolved | Valclei Ribeiro |
SEMPRE |
TV2134(C)SL
|
Working, but only with a vertical line in the middle of the tube | I had already checked everything, and it was the transistor that 606 makes the 5v on pin 2 of the migro | I had checked all the statements mentioned sound, I replaced the q 606 and resolved npn br8050 | FRANCISCO NASCIMENTO |
PHILIPS |
42PFL5508G
|
Standby light on and won't turn on | Defective pfc power supply oscillator, ic9801 | Stiltec | |
SAMSUNG |
UN43J5290
|
Won't turn on (dead), AC fuse open | Curto mosfets qm801cs e qm802cs (50r380) | Replace the mosfets and the 5a fuse and run to the hug | World TV - Sorocaba |
CCE |
STILE D42
|
It is completely inoperative, voltage of 5v with 5.1 and standby 2.8v. So I was suspicious of the 1.8 regulator, as it showed 1v at the output. | Ruins components: ec4 capacitor, 1.8v u5 regulator. | Solved just by replacing capacitor ec4, regulator 1.8v u5. | |
CONSUL |
CM020
|
It did not activate the magnetron, when the door was opened the plate motor turned and the lamp turned on | Small 12v relay burnt out on the board (relay that activates the fan and lamp), just replace it | reginaldo moronte,eletronica junior caldas novas | |
PHILCO |
PTV49F68
|
TV turns on without backlight, has audio, connect the separate LEDs but tsound is no image | Tcom shorted, 3 SMS capacitors shorted c 427,428,429, remove them all and insert a 47+24v electrolytic capacitor | Eletrônica Moura trindade | |
PANASONIC |
TC144M, TC146M,TC14C1U
|
It has high voltage, normal video and sound. but with a wave on the left side in the vertical direction. | C558 0.47(470k) for 400v with leakage. | Ademir tc. | |
PHILCO |
386
|
Does not have high voltage. | Resistor r444 18k aberto. | Ademir tc | |
SAMSUNG |
LN40C530F1M
|
Stand-by LED is on, when you press power nothing happens. normal voltages of 13v b and 5v a and b. However, voltages b turn on and off while a remains stable | Ci hdmi (ic 1101) shorted or with faults preventing the TV from starting and triggering main board protection | Remove the CI and test the board again on the TV, if it works, replace the CI with a new one | Eletronica SV - Guaira PR |
SAMSUNG |
UN48J6300
|
The backlight does not come on, nor does it blink after replacing the complete LED panel, in addition to a defect in the LEDs, also in the power supply, probably the panel and LEDs caused an overload due to a short in one of the LEDs and the power supply failed. | I.c position ic9101 (7014x / 1449) smd in the secondary of the power supply, it switches the 02 fets that feed the LEDs and also the position transistor qm885 | I replaced it because I had scrap, but I don't know the correct nomenclature, without time to open a schematic. interesting in this project, because although the power supplies come out separately from the connector that goes to the LEDs, in fact in the power supply itself if you observe the rulers go in series from to to apr, tsound are 03 pairs of rulers... that is, 02 + 02 + 02 in series. | MIGUELTV |
TOSHIA |
MS 9090
|
Only lights up stand bay | Crystal on the green pci card in my case | Eletrônica publisom rn | |
TCL |
65P65US
|
LED current reduction | Remove r628 and r629 which are connected to pin 2 of the ci, and place 01 of 47k in their place, note: the 2 resistors are in parallel | reginaldo moronte,eletronica junior caldas novas |