Repair Tips

Search:
Results: 87717

Make	Model	Symptom	Problem
SONY	CCDV8	Intermittent "y" signal	Viewing video on monitor through camera, y signal would becomeintermittent. was able to flex the me-1 board and cause the problem.found pin 2 on fl-701 was shorting to shield (inside). was not able toremove short, due to the size of shield. by squeezi
SONY	KV2697R	Tvi, suggestions	We contacted cable co. and have determined that rf signallevel is in 5-10dbm range. we have also tried to ground various parts ofchassis to true earth ground. -hq comments: please increase signal level in 15-20dbmv range, or tryexternal to set shieldin
SONY	KX1901	No video	No video, replaced ic301 twice, all voltages check ok.
SONY	CDP210ES	Unit always reject disc made by philips	Intermittently the unit will reject disc, will always rejectdisc made by philips, #411045-2, 1983, joseph haydn. checked adjustmentsusing the philips disc. the rf pll, gfs, 4.3218mhz and 918hz were good,the clv pll was bad. tried to adjust rv401, lost
SONY	KP5040	Poor registration, replaced ic5513	When first turned on after being turned off for a number ofhours, it was very poor convergence (the whole screen). the green wasaway from the red and blue.
SONY	TCFX210	P/n for head wires	We need the part numbers for the shield wires with plugs forthe rec/pb head (cnj301) and erase head (cn302). -hq comments: we do not have a service part of the shield wire withconnector. we have shield wire which is 10m long.1) 4 conductor wire with br
SONY	SL5800	No color & picture tearing	This unit had no color pbor rec. also the picture would tearwhen playing back a tape with chroma information.
SONY	CDP400	Door will not open or close	The door would not open or close when the eject switch wasactivated. we found the wire (4 conductor) between the eject switchboard and the function board to have an internal open. replacementresolved the problem. -hq comments: we ordered the wire from
SONY	CDP70	Incorrect wiring in service manual	Page 37 of the manual shows incorrect wiring in the area ofthe loading switches connected to ic106 and ic701. page 32 of the hard-wire diagram does not label two white wires on the loading motor board orthe three wires from s703. the correct wiring and
SONY	SL2300	Erratic system control	Only function that worked correctly was play. if you selectedff unit went to play/rew, went to play/pause/record/ff search.
SONY	HVF2000A	Part no for e8 ring	We need the part # for the e8 ring to secure the plate cover57 of the view finder hvf-2000a. we ordered the part with the part #7-624-112-01, but it is too big. -hq comments: the type listed on page 69 is incorrect (e8). the correcttype is de-8 (p/n 7
SONY	CDP30	Disc will not spin	Disc won't spin due to resting on table assembly. servicerhad 2 units with same problem. found in both cases that 2 of the 3supports for m703 spindle motor assy were broken off.
SONY	CDP70	No play	No play, disc spins backward briefly. found no 35 mhz. thisis second unit in one month with same problem.
SONY	RT44	Need diagram of bias osc area	I need diagram of bias osc. area on the power amp board. -hq comments: the schematic diagram for the area of ckt is in theservice manual on page 31.
SONY	KV1976R	Cb tvi, see sb ctv0288r	Customer experiences cb tvi through speakers, even with setturned off, but with master power on. same problem with power on, alsogets noise in picture. customer is a cb operator himself and seemsfamiliar with noise reduction techniques. tvi appears to
SONY	CDP302	Skipping the track specially on telarc disc	This disc has 20 track music. from 18 to 20, it skips usuallyfirst part of music, like from 0.00 jump immediately to 0.18 and so on.
SONY	ESR10	Popping noise at low volume on tape	At low volume there is a popping noise when playing back tape.appears to be spark plug related. happens only when in ford products.
SONY	CDP102	Noise in audio after warming up	Noise in the audio after the unit has been playing for 15-20min.
SONY	KV1956R	Intermittent no uhf, leaky capacitor not shown in s/m	This unit would intermittently shift from uhf channels tocable channels causing no normal uhf ch. reception.
SONY	STRV45	No audio output	No audio output. had audio to relay but relay was notengaging.