☰

Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search:
Results: 88224
Make Model Symptom Problem Solution By
PANASONIC SA-AKX100
SA-AKX100 		All voltages are normal, but the display does not light up 5 volts missing on pins 36 and 37 of the display Replace the d1001 diode on the main board. You can put 1n4007, it doesn't need to be fast. RUBERVAL
SAMSUNG UN32FH4003G
Bn44-00492a = bn44-00554b, with identical voltages and identical connection, identical LED current voltage. MIGUELTV
PHILIPS 32PFL3605D/78
LC10.1L+LLA 		Gray image, with horizontal lines and blinking R3j18 (r750k) aberto ( vgh_35 ) Replace r3j18 leitemarcellus
LG 32LN5400
Doesn't start Power supply Ic101 (ssc1s311a), r107 (22Ω), r108 (100Ω), q101 (mdf11n65b), c102 (330pf 1kv), f100 (t5a h 250v) - em curto/abertos Carlos Modesto
LG LN5400
Doesn't start Power supply Ic101 (ssc1s311a), r107 (22Ω), r108 (100Ω), q101 (mdf11n65b), c102 (330pf 1kv), f100 (t5a h 250v) - em curto/abertos Carlos Modesto
LG LN5400
Doesn't start Power supply Ic101 (ssc1s311a) Carlos Modesto
SONY KDL40NX655
No sound, or sound keeps coming and going Change headphone connector (green connector) <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
LG 42LD460
Does not turn on or standby C-457 and c460 shorted, leading to c-405, 459 and which are in parallel with the same symptom, also killing the 3.5v power supply. Replace of c-457 and c-460. EVALDO DE OLIVEIRA
SAMSUNG LN26B350F1
After a while, the PFC backlight +b turns off ok at around 388v, drive-on pin ok at around 4.7v Possible weakening of the lamps, the PCI was also damaged, the two 47/50v caps were replaced in series and that didn't solve it either. In the ci drive of the BD9893f lamps connected pin 10 to ground through an 82k resistor disabling the protection You tube - Direto no defeito
PHILIPS 20PT3331
White lines on top of the screen 2465 with 10mf, I had put a 47mf one and it didn't solve the problem and the voltage was at 12v and when I put a 10mf one it went up to 18v and the TV was normal. Eliel Magno
LG 55LA6210
Stand bay flashing and won't turn on C 2430 shorted is close to the connector that comes from the power supply Roberto
SEMP DL2970(B)W DL3270(B)W DL3970(B)F LE3274(A)W LE3974(A)F DL2971(B)W DL3271(B)W DL3971(B)F
The logo appears, disappears and so it stays, with BL and green LED Corrupt nand data Rewrite or replace nand davi.sls
PHILCO PH24A LCD
When you turn on the TV, the red LED stays on but when you press the power button it doesn't turn red and it doesn't work. On the main board tsound are 2 cis 3.3v regulators. one of them is not regulating the 3.3v. tsound will be less. good luck! João Carlos eletronica- Paulista- pe
PHILCO PH24A LCD
When you turn on the TV, the red LED stays on but when you press the power button it doesn't turn red and it doesn't work. On the main board tsound are 2 cis 3.3v regulators. one of them is not regulating the 3.3v. tsound will be less. good luck! João Carlos eletronica- Paulista- pe
SEMP TOSHIBA DL3271(B)W
Blinking LED does not turn on Diodo dp9 Replace without measuring in my case it was him EletroClaudiope
SEMP L43S3900
League without image. VD744 diode shorted. LOGANKLEITON
SEMP TCL 49SK6000
Turns on normally but the LEDs from the bad LED print do not light up Pdin pin in power socket burned out RJ ELETRONICA
PHILIPS 40PFG4109
After changing the LED bars, 1 bar does not light up The original buses have the central and positive pins with jumpers Jumper the central and positive pins on the middle bar and the bar that did not light up. (check the pins carefully so as not to jump with the negative). MarceloTJ
SAMSUNG HW-E450
SOUNDBAR 		Subwoofer box did not turn on stand by turned off Subwoofer primary power supply defect Replace do c.i. (1s1c01) - ice3br4765j PAULO PINHO
PANASONIC TC-L32U30
Turns off backlight and LED flashes 1x Remove protection -q7202 and q7203 oskarala