Aiwa Repair Tips

Search: aiwa
Results: 312

Make	Model	Symptom	Problem	Solution	By
AIWA	NSX-S201	Turns on, has all the functions but no sound.	Resistor 470r position r151 open. it powers the ic601 Audio modulator.	Note: some devices come from the factory with black glue covering the position of the resistor, making it difficult to locate.	ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it.
AIWA	CX-NMT70	Turn on and off	Changing the transistor position q110 (smd) it measures good but is defective bc846		simas433
AIWA	XH-A 1060	No sound and CD and tape mechanics inoperative	Without the 12v cold output on the fet on the sound card		carlos jpramos
AIWA	JAX-PK33	Device works, has no display	R908 open on transformer board		predador403
AIWA	JAX-PK33	Device works, has no display	R908 open		predador403
AIWA	CX-NS305-LH NSX-S305	Turns on at the same time comes back stand-bye	Transistor output short sound, q214-b1626, q212-d2495, was replaced and the same thing happens.	Replace sound outputs, and see there the transformer has a plate with a resistor type (pr005) it is open, put resistor 1r, putting vo, it works	This email address is being protected from spambots. You need JavaScript enabled to view it.
AIWA	NSX-SZ21	Doesn't read cd	Unit not found ksm-880 replace with sf-p101 not with kss213 keeps failing		Paulo.nickel
SOM AIWA	TODOS	Optical unit skipping skipping tracks	Defect in the unit cart motor,	Replace the engine. obs. To avoid warranty problems, replace the optical unit, preferably the original, good luck, professional friends.	fernando timbauba PE
AIWA	AR295	Does not turn on, normal power supply	R808, 816, 823, 836, 840 changed check all of 4k7		amsmariano
AIWA (SONY)	CX-NJ3	When you increase the volume it only turns off	Faulty protection capacitors are 0.22x2w position on board r149, r150, r151and r152	Replace the four with similar parallels or originals	jerson 37
AIWA	CX-NSZ51LH	Turns off when the sound is powered	Turn off transistor q130		caio
AIWA	CX NS 888 LH	Red LED lights up but just clicks on the relay and nothing lights up	Pro 005 open and diode 001 changed		moroni eletronica
AIWA	TV-AR295 RHB	With excess green and retrace of white lines.	The transistor q 710 shorted smd, thus increasing the voltage to 9 volts on the g output pin of the ic 101..	Your replace.	house eletronica ltda
AIWA	NSX-V420	Panel functions do not work correctly, only on the remote control	Solution: replace all touch switches		patrick
AIWA	NSX570	When I raised the volume the device turned off completely.	Q214 q215 smd can't be measured just by changing		vagner nardes
AIWA	TV-C1400EZ PT23CO	It didn't turn on or show a stand by signal	390k resistance r804 open	390k resistor replacement	LASC
SOM AIWA	CX-NF969	Shutting down, going into protection	Q224 k2937	Replace it, I couldn't find another one, I called it without it and it worked	This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós-PI,Ohm eletronica
AIWA	NSX-F12	5 cd carousel, motor does not have the strength to turn the carousel	33Ω r changed CD board feeds q401 to 406		Bruske
AIWA	NSX-999 0118	Panel lights up weak	Electrolytic c108 c107	Solved	EDSON
AIWA	NSX-S22	Nothing appears on the display	Open 27k resistor r116 is at the power supply