Cce Repair Tips
Search: cce
Results: 4834
Results: 4834
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS 2971
|
No sound | C661 | carlinhos | |
| CCE |
HPS 2971
|
No sound | C656 Shorted | carlinhos | |
| CCE |
HPS 2971
|
Só stand-by | He sucked a line | carlinhos | |
| CCE |
HPS 2971
|
R816 130k | carlinhos | ||
| CCE |
TV2918USP
|
Turns on turns off alone without image without sound black band on the left side with interference in the image when turning on and frame shifted to the right | C402,331pf 2kv | jair cap poço pa | |
| CCE |
HPS2197FS
|
Inoperative, LED blinking | Capacitor c825 47x160v e c 829 33x160v | Replaced everything ok | WILSON |
| CCE |
HPS2985
|
Normal power on.. screen shakes like power outage | Check the resistors r441. r442. r443 | R441. r442. r443 ......... pg | NEUPSX4DOWNLOAD |
| CCE |
HPS2007C
|
When turning on, stanby by kept flashing, it wouldn't start | The stanby by light kept blinking defective t 401 trafinho (open when measuring) | Replacement effect, it worked again, everything ok | Wilson |
| CCE |
HPS 2171
|
The normal channel appears after 2 seconds, causing some interference in the image and a blue screen appears | Channel selector | 28/08/12 | Flad 8 |
| CCE |
HPS-1401H
|
TV turning on with screen washed like fog with sound!!!! | When checking the vertical area, contact resistor 1 r fr402 of -12 was burnt and the vertical was shorted. | I replaced the vertical and the resistor and that's it, the TV was ready | heliomar |
| CCE |
2918USP/AV
|
Vertical closed in half, from the middle to the top of the screen. | N 301 ( stv - 8172a) partial short | Replace the same. | BARRETO CRUZ |
| CCE |
2918USP/AV
|
LED lights up, blinks 3 times, and does not turn on. | R - 423(10r) e vd 421 | Replace the same | BARRETO CRUZ |
| CCE |
2918USP/AV
|
Replace the same. | N 701 ( bl 24c08 ) | Replace the same. | BARRETO CRUZ |
| CCE |
TV2118USP
|
Then it turns on, it turns off and goes into low power supply protection, horizontal with just 100v, if it keeps insisting the flyback heats up along with the horizontal, note: the c417 was replaced, which was charred. | After checking the entire board (capacitors, transistors and resistors) there was only one missing! the flyback bsc25-0224k- was altered, replaced and everything works fine. | Flyback replacement (bsc25-0224k) and everything functional cool. | João - Palmares |
| CCE |
TV2118USP
|
Reduced image as if it were the deflector | Q406 leaking. | Replace q406 = 2sd2060 | JHONNES. |
| CCE |
HPS1479
|
Increasing volume alone | Key 2 c772 1n smd | Fernando R. | |
| CCE |
HPS1471
|
Increasing the volume alone | Key 1 c771 1n smd | Fernando R. | |
| CCE |
HPS 1471
|
Dark stripe on the side | C 425 / 47/160v seco | Flad 8 # 23/08 12 | |
| CCE |
HPS-1403
|
Dark images but when enlarged and lowered the screen gives a yellowish, almost green image with a black vertical bar on the left side | Change the 27k resistor 404 and measure from pin 41 of ic 501 tda 8841-2y to r-404- and from 404 to pin 24 of the processor ic 701=mc68hco5cc1 controller and check the complete track on the part of the white paint on the side next to the r-g-b output connector in my case it was a broken track under the white paint next to the r-g-b output connector - it was so perfect... |
JUVELINO | |
| CCE |
HPS2992FS
|
+ b horizontal above the value does not generate low power supplys of choper traffic | Trail departure pin 8 trafo chopper | Track rework | luiz2012 |