Cce Repair Tips

Search: cce
Results: 4824

Make	Model	Symptom	Problem
CCE	HPS1425	Defect: did not tune in to any channel.	Cause:r757 18k open
CCE	HPS-1415	No sound and image	C-101 open or shorted.
CCE	HPS1415	No vertical sweep.	Firstly, notice that the resistor (r420) that powers the vertical output will be burnt or intermittent. test the (ic301) and note that it will probably be shorted. Replace it with a new IC and the resistor. the television will work again, but with little height in the image, if the resistor burns out again, remove the ci and check the voltage that powers it and 24v, if it is above, change the capacitor (c458) coupled to the tsh, and another resistor (r420), and the device will operate normally.
CCE	HPS-14	Colorless and soundless	Q-801 (str 3125)
CCE	HPS/1403/2003/2006/2706	Stand by LED is blinking and the TV does not work.	Capacitor c-826 shorted or leaking.
CCE	HPS 2981	Shaking sides	It turns on and works normally for a few minutes, then the sides start to knock and the power supply emits a noise, as if the horizontal frequency is out. I verified that the power supply drops from 120v to 102v when the defect occurs. the image has a little excess white, I checked, the abl line (r 413, r 414, c420, d201, r206) is ok. solution: change all the power supply capacitors
CCE	HPS 2085 E TODOS QUE USAM O CI LA-7910	Channels go out of tune	Ceramic capacitor connected to pins 3 and 4 of the la 7910, check and replace if it is shorted
CCE	HPS 2080F	103v supply goes low when turned on and returns to normal	When entering stand-by, check r 805, which when open prevents the str 50103 from triggering at the same frequency as the horizontal.
CCE	HPS 2080	Heating up a lot c428 until it explodes	The problem was the flay back, which was causing the c428 to explode.
CCE	HPS 2070P	Vertical closed	1m8 open r-301 resistor
CCE	HPS 2070	TV stopped	Diode d807 or ic 705, also check components in the area.
CCE	HPS 2070	Buzzing at the power supply, doesn't work.	The first defect was the shorted diode that powers the +b of the fly-back (replace with original). On the first attempt to turn on the TV, it turned on with a green screen and white trace lines. I turned off the TV once and then when I turned it back on, there was no sign of life. After a lot of searching, I found a bf485 instead of the 2sc2236 (horiz driver). I decided to remove it and found a minimum leakage from base to emitter on the scale of x1. Just replace it and that's it. osb.: just replace with another original (2sc2236)
CCE	HPS 2025	Flashing glow	Defective diode d-201 1n4148
CCE	HPS 2003	Burning horizontal outlet	The defect was the horizontal outlet itself, I was forced to buy an original from an authorized dealer because the 2 (two) I bought in stores were of poor quality. the transistor is the bu2508dx.
CCE	HPS 14R	Vertical glossy stripe	D 411 burst replacing the same one heated burning reason c410 open, without capacitance. resolved ok!!!
CCE	HPS 1481	Height adjustment does not open the entire image, causing darkness at the top of the screen	C-607 causes excess noise in the +b of the vertical ci, without image and with sound, enlarging the screen, vertical closed was noticed, check r-315 of 1.8 m, another possibility is r 312=2.2r open.
CCE	HPS 1470	Everything works normally, all functions happen, when you put it on standby it emits a beeping sound from the speaker	Open or altered resistor r804.
CCE	HPS 1465	No sound and no image	Capacitor c- 413 330pf shorted
CCE	HPS 1430-R	Poor vertical deflection	Capacitor c-356 and capacitor c-357, if that doesn't work, change all the electrolytics in the vertical, it will work
CCE	HPS 1403 / 2003 / 2006 / 2706 - “DICAS” PARA CONSERTO	Does not turn on and the stand-by LED is blinking	Capacitor c826 (code 491010104) leaking