Cineral Repair Tips
Search: cineral
Results: 427
Results: 427
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CINERAL |
21PCIN0405
|
No image on av | I short circuited pins 13 and 14 of the 4053 switch | Marcelo | |
| CINERAL |
14N CIN
|
Image shifted to the right, black band on the left and no characters | Position smd diode d408 | Replace d408 | Fofao estância |
| CINERAL |
14N CIN-0401
|
Does not turn on or stand-by when the weather is cold. By exposing the TV to some heat power supply (e.g. getting hot in the sun) it turns on normally. | Defective primary power supply electrolytics or low capacitance. | Replace with new or in good condition. preferably, replace all the primary electrolytics (including the 150 μF "biteludo" for 400v). If you need a schematic, use the Philco ph14 "game" one. | Tiago C. Neves |
| CINERAL |
CIN-401
|
Disappear image, lit filament and normal sound. | Poor abl tension. leaving the screen very dark the image remains, increasing screen some image | C415 470μF x 25 v | Pardal-x |
| CINERAL |
TC-1433N
PTFM05-1 |
Dead TV wouldn't even turn on standby. | When removing the q 404 (horizontal output) the TV oscillated, damaged the degausser relay and lit up the LED, and the cause of the q404 burning was the shorted flyback. | After exchanging the two, I just ran for a hug. | Marcio eletronica |
| CINERAL |
TC1466
|
TV turns on and off immediately | Only replace cap.318/4.7/50 | I | Adão S L |
| CINERAL |
R-FLAT 2166
|
Does not turn on LED blinks without power supply +b oscillating 10 to 14v | Q804 = c1815 defective | Replace for a new one | EletronicaAlmiro |
| CINERAL |
29P CIN 0507
|
Pink image. no green. | R 520 (2k7) | NEW PEK ELETRÔNICA | |
| CINERAL |
29P CIN-0507
|
Unlock without control | Improper programming | Leonardo | |
| CINERAL |
29P CIN-0507
|
Has sound but no image | Open resistor 6.8k position on board r432 | Replace with new | <small> |
| CINERAL |
TC-2033N
|
Ticking ticking and low secondary power supply | Solved 130k resistor r 834 open | Replace r834 | beto2828 |
| CINERAL |
TC-1470
|
Vertical closed | Q102 | Replace q102, put bc337 | Marcelo Piranga |
| CINERAL |
21P CIN-0405
|
It turns on normally but with a black bar on the left side of the screen. | Q409 | Replace the c409 in the fly-back foot | Sinailson furtado |
| CINERAL |
29P CIN-0507
|
Inoperative, does not turn on, LED is off | Ic 801 with faults | Just replace it and the TV is 100% | Nilson Rodrigues |
| CINERAL |
TS 2944
|
Connects white screen with lines | Resistor on the 210 volt line for the tube plate | I replaced the resistor and a diode close to the tda 6108 on the tube board and the tda was also bad, I replaced it, solved | Samuel silva |
| CINERAL |
21PCIN 0305
|
Closed and inverted screen | Tip arock hit.. | Replaced the 301 for another... I didn't have a 4001 and replaced it with the 4004 | Mauro |
| CINERAL |
21P CIN-0405
|
Doesn't start | Photo coupler | Replace | davi.sls |
| CINERAL |
CIN0305
. |
Does not turn on LED. and when it turns on, it only turns on via the control and with the vertical closed at the bottom. | The reason why it only turns on via the control is the keys on the keyboard. and the cause hanging with closed vertical is the eepromm memory. note; also change the 100/35 volt c302 which was exhausted. | Replace the keyboard keys and the c302 with 100/35 vertical turns. | <small> |
| CINERAL |
TC 1470
|
Vertical risk (without horizontal deflection) | Open capacitor c214 | Replace and run.... | Matrix |
| CINERAL |
R-FRAT 2166
40-ONX 56BMAF-1XG |
TV didn't light up OLED but had +b 105v normal but didn't have 3.v | Capacitor c872 of 100mf at 16v, a 100mf at 25v was placed and the TV looked great | Don't thank me but thank the electronics | <small> |