Cineral Repair Tips

Search: cineral
Results: 427

Make	Model	Symptom	Problem	Solution	By
CINERAL	PL-2910P	Power supply oscillating and led blinking	Transistor tl431 position v540 shorted		This email address is being protected from spambots. You need JavaScript enabled to view it.
CINERAL	TC-2910P	It turns on but there is no image, it oscillates very weakly and makes a noise on the horizontal stage.	Check the voltage -15 and +15v, if they are low, change c474a 100/25v -15v.	This chapter. It was out of capacitance, I replaced it and it turned on normally. Hugs.	Eronaldo
CINERAL	TC2070	Vertical closed	Q 102		This email address is being protected from spambots. You need JavaScript enabled to view it.
CINERAL	TC1444	TV stopped, LED blinks and doesn't start.	C2224 of toasted blue disk and r2251= i r connected to pin 2 of the fly-back at + b, open.	C2224 and r2251 were replaced and everything was ok.	Armando de Olímpia
CINERAL	TC1444	White screen with mixed colors	Fr217 open	Replace that resistor and that's it	orlando
CINERAL	TC-PL2910P	It only works by removing the vertical drive	Replace all vertical power supply and -14v +14v power supply capacitors,		marcos hi-fi campinas
CINERAL	TC-PL2910P	It only works by removing the vertical drive	Replace all vertical power supply and -14v +14v power supply capacitors,
CINERAL	TC-PL2910	Turns off after 2 minutes	10m 160 v electrolytic capacitor failure. position on chassis c458	Changing the electrolytic.	AJARBAS
CINERAL	14N -CIN-0401	Reduced frame forming a trapezoid	Defective deflector	After checking the power supply that feeds the +14v vertical that comes from the pheybec and the pulses coming from the ci, everything was ok, at first it seemed to be a memory defect but it didn't go wrong, I replaced the deflector and it was ok.	moroni eletronica
CINERAL2070	TC2070	Only stays in stand bay	Cause: capacitor c214 of 330k x 250v without load also damages the cap. c213		klein
CINERAL	TC-PL2110	Noise on fly and turning off	C-215 damaged	Replace c-215 without measuring.	jean alves
CINERAL	TC1466	Q881 shorted and r881 open, after exchanging them, q881 shorts out again	D881 open	Don't forget to also replace the d891 and d892	Eletronica Millennium
CINERAL	TC 2070	It has a normal power supply, not the standbay, the micro pins (59,61,66) were supposed to have +3.3v but it has almost +9 v.	Dz 107 and q103 altered (with leak).	Replace them and the TV was fine.	loco Assistécnica
CINERAL	TC 2070	It has a normal power supply, not the standbay, the micro pins (59,61,66) were supposed to have +3.3v but it has almost +9 v.	Dz 107 and q103 altered (with leak).	Replace them and the TV was fine.
CINERAL	TS2977	Device with excess width	C227 electrolytic cap10x160v		Claudio-Jardim Paulista
CINERAL	21PCIN-0405	Turning off by itself	Cold solder on the fly back pins	Resoldar ok	ELETROCLAUDIO AGUAS BELAS
CINERAL	TC1470	Does not pick up uhf/vhf channels or glitches	Fr238 from 12v power supply	Replace (1r)	Dirso
TV CINERAL	TC 1433 N	TV stopped, it can't arm the power supply, it keeps pulsing, cineral tc 1433 I've already changed the electrolytic capacitors on the power supply and nothing.	Resolved 130k r 834 resistor and power supply photocoupler.		BF.COLATNO
TV CINERAL	21P CIN0405	This TV arrived stopped, it just stays on standby, +b is at 75v, even turning off fly and horizontal output.	I changed the eprom.	Resolved.	b
CINERAL	21P CIN-0405	Burning q846 ss8550 and the TV keeps turning off	Short sound output	Replace the output and the q846 ss8550	Eletroclaudio Aguas Belas PE