Lg Repair Tips

Search: lg
Results: 4961

Make	Model	Symptom	Problem
LG	STUDIOWORKS 775N	Horizontal width does not work reduced frame.screen reduced horizontally.no adjustment	Changed r736 (100k, 0.25w which was open. studioworks 775n does not turn on, led blinking. when turning on the power the led blinks alternately (green and orange). I got one of these, with the same defect, the front led kept blinking, red and green, and it was the video amplifier IC that is on the crt board....
LG	STUDIOWORKS 775N	I can't increase the brightness of the monitor, I heard that increasing the value of a resistor solves the problem, I ask what the resistor is, as I don't have a diagram of this monitor???	It has two 380k resistors, r778 and r799, in series. increasing this resistance, you increase the value of voltage g2.
LG	STUDIOWORKS 76I	Video pre amp ic(0imo132820a ic,motorola mc13282ap) is no longer supplied	Corrective action. change ic301(0imo132820a ic,motorola mc13282ap ndip 24 bk pre amp) to ic301(0imo132820c ic,motorola,mc13282ep ndip 24 bk pre amp). when changing mc1328ap(ic301)to mc1328ep(ic301) additional work is required. (applied model: s/w 76i, 76m, 76t, 76w) - additional work. You need to add a jumper between pin #9 and pin #17 of ic301 on the back of the video pcb.
LG	STUDIOWORKS 575N	I have this monitor on the bench for maintenance and I found q719 shorted, but it's a strange number, I think it's a fet, but I'm not sure, could anyone tell me which component is used for this place???	2sj306, see the diode connected to it. I already checked and it's ok, what I want to know is which transistor should I put in place of the 2sj306 as a replacement. This is not a common fet, it's a p_channel fet and it's 250v by 3a, You can use any fet with these characteristics, remember that it is a 250v p-channel fet. note: see 2sj307 which is 250v for 6a.. friends I have several pumps like these on the bench what is their 719 and the irf 630 if there is another one it is good to know
LG	STUDIOWORKS 575N	With normal but weak image (low brightness and low contrast)	The filament voltage was low 4.5v the cause was the c926 1000mf/16v
LG	STUDIOWORKS 575N	When I turn it on, the power LED comes on and for about 3 to 4 seconds you hear a clicking sound coming from the power supply (I think it comes from the power supply relay) and the LED goes off and on continuously and the clicking continues each time the LED flashes	I have already disconnected the fly-back and the problem continues, I measured the voltage at pin 2 +b of the fly-back and it varies from 115v and rises to 195v then drops to 115v and rises again to 195v. check q706, if ok, check if there is 194v on the +b line power supply, if ok check pin 2 of t701 if there is a signal with a frequency of 31khz 60 to 69khz 160v, if not ok, check q717, q718, q719 and d707, If ok, see the waveform (signal) on the q705 collector, if ok, the flyback remains, replace it.
LG	STUDIOWORKS 563A	Def. a little crazy, he calls whenever he wants	I tested all the secondary components of the power supply plus the tsh, the vertical output, fly-back and I didn't find anything abnormal. Have you taken a look under the plastic grille of this monitor, I don't know if the defect is the same as the one I had, but what I had was that the image disappeared or didn't even appear, it was a jammer through which the tube filament feed passes, the solder was It's broken and it's right under the plastic grille, without dismantling it, you can't see it.
LG	STUDIOWORKS 560N	Does not act on the width and has a cushion effect, perhaps because it is too wide	I replaced the 2sd669 transistor which was shorted and everything was in its place
LG	STUDIOWORKS 561A	Noises coming from the monitor	Modify r909(1k --> 5.1k). Add the capacitor between the c943 ground and q928 emitter. 3.add hot glue (jet melt type) to the capacitor.
LG	STUDIOWORKS 560N	Without full width and height opening	Swapped q801 and 802 (both with leaks in the last scale of the multimeter) caused the r 939 of 3.3Ω to heat up, but what probably burned it was the short in the ic 701 kb 2511. the short in the kb by its pin 28 must have damaged the two transistors that had perhaps not activated the irf q 804 (detail: I had already removed this irf, doubting that it was stealing current from the power supply)
LG	STUDIOWORKS 560N	It turns on... but no image appears	The problem is that the secondary voltages are very confused... and the power supply transformer keeps making a strange noise, not the typical "tick tick tick" but a continuous noise... with some oscillations...... o b+ the fly back has 37v. I isolated the tsh to measure the voltages, everything went back to normal... but after about 2 minutes without the collector, the capacitor c837 100uf x 100v smoked... I already replaced it, and when I isolated the b+ for measurement, the irfs630a burned out too....I already replaced it too.......is it the flyback, friends?..the biggest problem is that I already tested it on that Diatron test device, and it was good! .... it was the flyback... exchanged and it works again.
LG	STUDIOWORKS 560N	This monitor is excessively wide and has a cushion defect. When I try to adjust, the LEDs just keep flashing	I've already replaced the ci kb2511 and the 669 width transistor. I placed two fet irf640 transistors in positions q507 and q550, but I don't know if they are the original ones. I also need to know the value of the coil l502. A question if you remove the q506 2sd669 from the circuit
LG	STUDIOWORKS 560N	The flyback was exchanged for an original one, but when it starts, it goes out and makes a few clicks with the front LEDs flashing.	The problem will be solved by replacing the .047 x 25 electrolytic capacitor that is located on the power supply's primary.
LG	STUDIOWORKS 520SI	Brightness increasing in intensity and panel brightness potentiometer does not work	Replaced the 2.2m resistor r871. studioworks 560n does not turn on, it ticks and the demagnetizer relay hits. LED keeps flashing. change the following electrolytic capacitors in the power supply primary (even if they look good on the capacimeter) the 2 47mf, the 4.7mf the 2.2mf the 0.47mf (it has to be this value!, in case you can't get one , connect two 1mf in series, respecting polarity. Of course, this monitor can present the same symptom due to other problems such as shorted horizontal output, flyback, etc... but in the specific case of this monitor, the problem was this.
LG	STUDIOWORKS 57I	He keeps trying to set up the power supply and send high voltage and he can't but if he waits for a while he tries, sometimes he sets it up and sends high voltage but this rarely happens and when he doesn't succeed he just sets up the power supply but doesn't send high voltage (the tube does not light up).	Defective flyback
LG	STUDIOWORKS 57I	When you increase the contrast or the screen, it increases normally and after a drop in contrast, it seems to saturate something and make the contrast "much"....	A common defect that causes one of them is to change one of these two resistors r743 or r742, both 680k. Changed the resistors and it started working again. studioworks 57i when I turn it on, the monitor goes up and then turns off. g1 and g2 are without tension. If your monitor uses the fly 6174z-2001g there is a high chance that it is defective, when this defect usually happens the fly and the ci that goes next to it must be replaced It is a kia358 the position if I am not mistaken It is ic704
LG	STUDIOWORKS 56I	Brightness flashing on the screen, back and forth (instability)	Replace o flyback
LG	STUDIOWORKS 55I	Turns on the LED, the filament does not light up and when turned on, it makes a frying noise around the fly	Flyback shorted.
LG	STUDIOWORKS 55I	There is no image	Exchange of r871 2.2m
LG	STUDIOWORKS 55I	With cushion effect	Q753, q751, ic701, r761, q752 and peripheral components, Of course, this wide transistor always has cold soldering problems, check this.