☰

Mitsubishi Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: mitsubishi
Results: 1346
Make Model Symptom Problem Solution By
MITSUBISHI BDS28WS 11AK19
11AK19 		Entering service mode First enter the installation menu, then press 4, 7, 2 & 5 respectively (another possibility is 2,3,5,7)
MITSUBISHI BDS28WS 11AK19
11AK19 		Dead apart from led dimly flashing green - will sw on & off - no eht and ht (150v) low at 102v D807 in psu leaky
MITSUBISHI 11AK19
11AK19 		Dim band of light 3/4 up screen - sound ok D408 8v2 zener leaky
MITSUBISHI BLACK DIAMOND 11AK19PRO
11AK19 		No pic then e/w faulty C630 dry jointed, when resoldered had e/w fault - q603 leaky fitted buk457-600b in lieu also l604 faulty
MITSUBISHI BLACK DIAMOND 11AK19PRO
11AK19 		Dead with d829 uf5407 ht rect s/c D807 ba159 s/c, chopper tr s/c 2sk2545 - used 2sk1507 in lieu, r817 2r2 5w o/c
MITSUBISHI BDS28WS11AK19PRO
11AK19 		Won't come out of st/by when sw to st/by aft operating for more than 5 mins Sw mode tr replaced
MITSUBISHI BDS28WS11AK19PRO
11AK19 		Sw to st/by after 2 mins - g led flashes when trying to come out of st/by D505 2v4 zener sm conn to pin 33 ic501 leaky
MITSUBISHI BDS28WS11AK19PRO
11AK19 		Dead Q605 bu2508af, c630 390nf 250v, c626 12nf 2000v, l604 e/w coil, tr601 line drive transformer, l604 15mh coil, r629 27r, d807 ba159, d605 ba159, d606 ba159, c835 1nf 1000v
MITSUBISHI BDS28WS 11AK19PRO
11AK19 		Int shuts down to st/by with led dimming - usually at start up Focus spark gap arcing - replaced crt skt 30001855 ?1.39 from seme
MITSUBISHI BDS28WS 11AK19
11AK19 		Int blows loptr at sw on - also ew fet & r629 could be damaged Dry joint c630
MITSUBISHI HS MX1
No color Switched to mesecam Force to pal pin 1 of ic 6a0 go to low level remove r 6n2
MITSUBISHI HS MX1
No display and won't turn on Q 901 = already 101 Sub q901 = bc 638
MITSUBISHI HS MX1
No display and won't turn on Q 901 = already 101 Sub q901 = bc 638
MITSUBISHI CT 14M1 EPM
With little sound and noise Qaa = JK501 = SZ15
MITSUBISHI HS MX1
No color Switched to me-secam Force pal pin 1 of ic 6a0 to go to low level remove r 6n2
MITSUBISHI CT25M1
E/w does not adjust well vertically folded at the bottom Sub c587 = 2,7n 2000volt
MITSUBISHI CT25M1
E/w does not adjust well vertically folded at the bottom Sub c587 = 2,7n 2000volt
MITSUBISHI TC-1498
Defects, no image and no sound, normal 33v voltage, good selector. Cag trimpot altered, replace with a new one.
MITSUBISHI TC-1631
Call whenever you want. Change resistance r-916 or r-915 of 150r
MITSUBISHI TC-2030
Defect becomes negative after some time. The 10k x 50volt ceramic capacitor (.01µf) was replaced. Ceramic shorted.