Panasonic Repair Tips
Search: panasonic
Results: 2900
Results: 2900
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PANASONIC |
SOM
SOM |
Error codes | -"f15" sw reset failure the cd does not work. This message appears when the s701 is not activated and/or is damaged. -"f16" s3(tup) failure, the cd does not work. This message appears when the s701 is not activated and/or is damaged. -"f25" s4 failure (dro) this message appears when the s4 is not activated and or is damaged. It is related to loading and unloading CDs. -"f26" CD servo failure, the CD does not work. This message appears when the power supply detects failures in the CD system -"f27" s5 fault (tno) appears when the s5 is not activated or is damaged -"f28" failure of s5 (stk, s2 (ply) when loading the cd it does not do it correctly -"f75" cd power appears when ic501 is deficient. | ||
| PANASONIC |
20KL2
|
Image shifts to the right | D558 | ||
| PANASONIC |
14C7
|
Horizontal beeping | Changed 56v zener | ||
| PANASONIC |
TC-14C5
|
Tc-14c5 does not work because the power supply is too low | D-818 shorted | ||
| PANASONIC |
TC-20C6
MX1 |
Trigger protection | Vertical circuit la-7837 | ||
| PANASONIC |
TC-29S10
|
Horizontal flashing open date | D555 - zener de z, shv (ma 165) | ||
| PANASONIC |
SA-AK15
|
No functions on the keyboard or with intermittent functions | Cold soldering on the micro | Solve micro | |
| PANASONIC |
TC-20A12
|
Low 3v supply doesn't work | C625 shorted 220mf/6v | ||
| PANASONIC |
TC-20A2
|
Low 3v supply doesn't work | C625 shorted 220mf/6v | ||
| PANASONIC |
TC-29KL03
|
Closes the vertical at the bottom | Capacitor smd na saida vertical | ||
| PANASONIC |
TC-21FX30L
|
Turns off in a few seconds with a dot on the screen | As a testimonial | ||
| PANASONIC |
TC-14RM15L
|
Turn on and off | D403 short or open | ||
| PANASONIC |
TC-29Z99L
|
Turns off intermittently | R518 change value to 3.3 r | ||
| PANASONIC |
TC-29Z99L
|
Turns off by itself | D511 with leak | ||
| PANASONIC |
TC-20G11 TC-29G11 TC-29A11
BR2 |
Function keys blocked, only power works. remote control works normally. | The keys were probably blocked by a TV function. | Enter service mode: with the television on, press the action and power keys simultaneously for 3 seconds. To exit service mode, press action until exit. | Renato Pareta |
| PANASONIC |
TX21MD3
EURO2M |
I'm ok htoff | +b3 off- f851 open | Burnt trans hdriver | pernalonga |
| PANASONIC |
TC14A04
|
Acting protection | Q-840 smd | To remove | luciano |
| PANASONIC |
TC-14A12
|
Image shifted to the right horizontally with a white "cloud" above | Cause: d558=ma185 shorted. obs. you can put 1n 5061 and it works fine. | Other substitutes: ba157, ba173, bay21, bay46, baw52. good luck everyone. | |
| PANASONIC |
TC20A10
|
Does not oscillate | Short vertical | Replace | ELETROCLAUDIOPE AGUAS BELAS |
| PANASONIC |
TC 20A10
* |
With vertical lines turning off in less than 5 seconds. It was changed and after being resolved, it turned on normally with no image and a blue screen appears. | C-452 and c-829 and r-106 amended | Your replace. | eletronica wagner |