Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PCR-1447
|
Generates and cuts at the same time | 10k open r-707 | Ramiro Lima | |
| PHILCO |
PCR-1447
|
With image and sound, little brightness | 10k open r-714 | Ramiro Lima | |
| PHILCO |
PCM-2044
|
Without generating, but with the +b, led blinking and killing horizontal oscillator voltage | Micro-m37210m3-709 | Ramiro Lima | |
| PHILCO |
PCM-2044
|
It works and picks up some channels, sometimes it freezes on just one channel. | R- 113 open 22k | Ramiro Lima | |
| PHILCO |
1443
|
Without generates, and without +b. | R-711 open from 6.8r | Ramiro Lima | |
| PHILCO |
PCS-2956N
|
Interference in the image, RF type | C208 | ||
| PHILCO |
TP 2052
|
Does not tune channels - autoprogramming does not capture channels. | Transistor q201 bad. was open, cutting +b from seletronic | ||
| PHILCO |
PCS-2700N
|
Image disappears after a while | Check cable welds to kinescope board, r708, solder on kinescope board | ||
| PHILCO |
PCS2976S
|
Dead | Ss09 | ||
| PHILCO |
TPF-2940
|
No audio in rf | C401 e c402 | ||
| PHILCO |
TPF-2130
|
Does not turn on, relay keeps tripping | Solda em r931 18r 2w | Edgar | |
| PHILCO |
PT2053
|
It doesn't turn on, but the LED keeps flashing. | DS08. | Cold solder on the anode. | Paulo Augusto da Rocha Júnior |
| PHILCO |
PCS-2976S
|
Vertical varies at the bottom by a few centimeters | Possible cause r910 and r912 | ||
| PHILCO |
PCM-1446
|
Wavy image | C-905 220mf x 400v | ||
| PHILCO |
TPF 2130
|
It doesn't work, the 9v power supply is missing | Absence of 9 volt power supply (bad contact on r 931) | Resoldei o resistor r 931 ( 18rx2w) | Leônidas (Léo) |
| PHILCO |
PCS-2956
CP01LR01 |
East west defect | Reduced condition with cushion effect symptom | Solda fria r 722 10Ω | Airon |
| PHILCO |
PC-20R42
|
With image turns off | R723=27k e c310. | Andrade Sequeira | |
| PHILCO |
PCM-1446
|
Doesn't tune in | Reset: with the TV off press: channel+ and channel- simultaneously turn on the TV, when the LED goes out it starts working | ||
| PHILCO |
29S4F
|
Does not work on remote control | I already got this defect, I just had to reset it by doing the following procedures: if the ic101 version is tda9370 n2 and tda9373 n2, proceed like this: unplug the socket, simultaneously press the "menu and volume-" keys on the front panel, turn on the plug plug into the socket and wait 10 seconds, after this period, just release the "menu" key and keep the "volume-" key pressed for another 2 seconds, turn on the device using the "power" key. | See forum philco problems with remote control | otaviano |
| PHILCO |
TPF 29S4F
|
Generates and cuts in 3 seconds | C-1703 value 5k6 open | ramiro lima |