Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PH21SS
|
Alloy with 60% black screen on the bottom and 40% blue with shrink lines | Replacing the VD401 diode cold solder on the transistors V503 V505 V574 | Worked perfectly | ELETRONICA AUTO TREVO |
| PHILCO |
TPF-2130
|
It makes a dragging noise and turns off and the standby LED flashes. | Poor contact on c922 (220uf 160v) on the power supply secondary. | Resolder | Manoel (Noca) |
| PHILCO |
PC20R42
|
No noise at the power supply | Horizontal side bu2506dx and 6n8 1k6v capacitor | Replace of the same | orlando lott |
| PHILCO |
PCM 1446
|
LED lights up but doesn't start | Zd904 shorted | Replace | ELETRONICA MEDEIROS |
| PHILCO |
PCM1444
|
Does not turn on, power supply keeps pulsing and with retrace lines | The reason for this defect is the fly back that leaks high voltage | Replacing resistor r 715 and fly back | ELETRONICA GAZZIN - felipe |
| PHILCO |
TP20V56
|
TV doesn't turn on | Open r911, ic 901 oscillator, capacitor c 948 smd | Replace r911 2m2, replace ic 901 oscillator, replace capacitor c946 smd for ceramic 271k | ricardo quadros |
| PHILCO |
TP2052N
|
No part of the LED goes out, it's the only part that stays on | Fly back | edezio eletronica es | |
| PHILCO |
TP2052N
|
After turning it off, it won't turn on again. Just let it cool then turn it on again | O c708 de 470pf2kv e c709 1k5 2kv ambos no horizontal | Direct replace | Ademar |
| PHILCO |
PCM2046
- |
TV turns on normally, but without characters (menu and channel number) | It's funny | Replace tda3653b | franciscoMc |
| PHILCO |
PH21SS
|
Vertically closed up to 80% of the screen or closing from the bottom to the top and turning off in the latter case. | Replace diode vd564 (fr154) the byv27-200 can be placed. replace directly without testing. | flaviosel | |
| PHILCO |
PHT660
|
Dead | T1 shorted d18 and d20 shorted | Replace parts and that's it | orlando lott |
| PHILCO |
PCS 2976S
CPH04 |
Burning vertical outlet | R 919 and r917 causing high power supply | Replace r 919 120k without measuring | luiztvsom |
| PHILCO |
PCS-2976
056022 |
It turned on and then turned off, turning off the standby light, when I turned off the deflector coil it turned on. From the beginning I thought it was the power supply but it wasn't. | It was the capacitors c730 and c715 with loss of capacitance | And just replace and run to the abrasion. | diego lima nova timboteua |
| PHILCO |
PCM1446
CPH-05M |
Sem osd | R714 (1k8) | ||
| PHILCO |
TP20V56
|
Does not turn on, power supply inoperative | D915 (r31) shorted | I replaced the r31 diode with a 1n4148 and it worked fine. | digitec eletronica by lambarí d'oeste-mt |
| PHILCO |
PH29C
|
Turns off in 5 seconds | No image, when the screen increases it turns white and turns off quickly (diode open) | Replace open diode d811 | cesar_unitec |
| PHILCO |
PCM2044
|
Sometimes it turns on and sometimes it doesn't turn on and the LED just keeps blinking | C706 22n close to the power supply output capacitor | edezio eletronica | |
| PHILCO |
PCS-2950
|
Vertical closed and burning la7838 | La7838, zd601 and zd602 next to the fly back, were changed | Replacement | Eliel |
| PHILCO |
PCM-2046
|
Oscillates and stops, makes a very strong horizontal noise | Pin 10 of the one chip shorted | Replace | |
| PHILCO |
TP-2054
|
Normal carioca power supply, the high voltage in the "pacifier" bursts and it doesn't turn on. | C715 with "cold" solder. | Clean it, because it's charred, resolder it, and that's it. OK? | derli souza |