Philco Repair Tips

Search: philco
Results: 4775

Make	Model	Symptom	Problem	Solution	By
PHILCO	PTV-28G50SN	TV turns on without picture	Shorted smd diode and stuck smd fuse on board v.com	In my case it was just the two defective components, I replaced them and the problem was resolved.	jose fernandes dos passos
PHILCO	PH32M3	Turns on, everything is normal, after a few minutes, video disappears, back light is on, keyboard doesn't work.	Capacitors ca08, ca10, ca 15.	Replace of the aforementioned capacitors.	arock
PHILCO	PH32E32DG LED	Totally off	24v power supply rectifier diode, position d1d0	Substituir	Matões Assistência Técnica
PHILCO	PH19B16DM	Turn on the TV and the screen keeps changing color without any characters	With the power supply in place, I grounded a wire and passed it to the CI u201 pins and then I assembled the TV and it went back to normal.		fabiusmax
PHILCO	PH32E20DSGWA	Leds writer	Changing three 100/50 and one 470/25 capacitors in the power supply secondary.		Danubio
PHILCO	PH21B PH08K-A (VER:0.7)	Vertical almost completely closed, open only about three centimeters halfway up	Defect a 39k precision resistor changed to more or less 70k in position r 320 close to the micro		Jr eletrônica
PHILCO	PTV32D12D	Mute, without sound	Ca23 close to the sound output.	Replace	Marcondes Ohm Eletrônica Jaicós PI
PHILCO	PH21M SS	Does not turn on with a small buzzing sound and heating up a lot r402	D815 open rectifier		Marcondes Ohm Eletrônica Jaicós PI
PHILCO	PTV32D12D	Audio only.	LED bars with open LED.	I removed the rb840 inverter resistor (4r7) in a previous repair. but returned in 2 weeks with problems with the LED bars. I replaced the rb837 resistor (3r) with a 3r3 one. The measurements were 61.7v and 248ma, it was 58.7v and 168ma. I hope tsound is no return.	Eletrônica R-Tec
PHILCO	PH14D CCP-3400	TV stopped does not turn on stand by	R822 470k changed to 670k	In this case it was resolved	Wellington TV
PHILCO	PH21 US A1	R407 pifado	Charred	Replace the 1k r407 this resistor has a plate that comes with the number r407 or r460 the value is the same 1k	Sinailson furtado
PHILCO	PH29B	Tsound is an image but no sound, the sound is only available in AV mode and not available in TV mode.	I changed the capacitors upholstery c833 and the others near it resistors diodes but it stayed the same way I saw the voltages were giving 12 volts arriving at the ci 7266 amplifier I put sound signals to see if the ci was amplifying pins 4 and 12 and it was yes I put them in the micro was also yes, until the amplifier I changed the micro processor and nothing	My solution that solved it was the epron ic 202 that solved it	Parente maia
PHILCO	PH58E38DSG	Turns it on, writes philco and between 12 and 15 seconds the TV turns off the philco and has a dark screen, but the LEDs are on and it turns off completely and goes into stand-by. If you press power it accepts and does it all over again.	As the manufacturer informs, this symptom is related to the LEDs, but to my surprise I risked updating it, which I downloaded from the website itself and the TV was perfect. detail that if it was an LED, when disconnecting pin 4 (fail) of the cable that goes into the LED drive board, the TV was supposed to work if it was a defective LED and actually the TV, even with the fail turned off, did the same, it turned off afterwards 15 seconds....so that's why I risked the update	Update software.	MIGUELTV
PHILCO	PH32M DTV	Turns on and off (backlight defect)	R-0 of the inverter board	Resolder or replacement	Maike sorriso-MT
PHILCO	PH32M DTV	TV turns on without characters.	Poor contact on jumper cn17, not allowing voltage to reach the screen connector	Remove jumper and replace	Reinaldo
PHILCO	PH32M DTV	TV does not turn on (green LED on)	Measure voltage on regulator u36, tsound must be 1.8v at the output. the input comes from jumper cn17, passes through diode d76 and enters u36.	Replace d76.	Reinaldo
PHILCO	PTV40E21DSWN	Doesn't start. standby LED off.	All normal voltages in the secondary, except in the nu2p2 ams1117 3.3v regulator, which had only 2.75v at its output. This defective regulator was replaced and the device started working normally again.		Isidro
PHILCO	PH28B25DG	It has sound and no image. burning LED bus.	LED bus voltage above 30v (in my case it was almost 32v)	To lower the voltage on the LEDs, you must replace r610 from 10k to 18k. the voltage on iset pin 6 of the mp3394 must be 1.20v. and 29.5v LEDs.	EvandoViana
PHILCO	PH21D	Doesn't start	D820		Rual de saja eletrônica R.E
PHILCO	PH32F33DG	Take away characters in the bottom left corner. It keeps showing: mv v8-0ms32la-lf1v017 sv v8-0ms32la-lf2v003 id 64 adc ng p network ok	After an update it looked like this.	Using the remote control: press menu>image>go down to contrast>type 9735>factory hockey and turn it to "off">remove the power cable and it's ready.	Eletrônica R-Tec