Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PMS24	When opening the door, the light turns on and the prosto and fan rotates	Main relay below the transformer		Ahumaky
PHILCO	PH28S63D	Does not turn on, no stand by.	C8 shorted.	Replace: c8, r20, q2, f1, r15(10r smd), r15a(10r smd).	electronicssupplyparts - Gramado/RS
PHILCO	PH39R25DSG LED	Sound without image back in the background	Burned out LEDs and diode on the power supply board	Replace LEDs and the d10 diode of the power supply	Tec center
PHILCO	PH32U20DSGW	Doesn't start	Diode dp202 - primary power supply		Pardal - X
PHILCO	PTV55U21DSWNT	No image and the screen LEDs do not light up	At the power supply in short d27 and 29 (sb5200 is scotly)	Replace the diodes	SANTOMEL
PHILCO	TP1452N	Completely turned off, the power supply with a filter capacitor voltage of 300v, 12v power supply zeroed.	470k open resistor	Substituir	Matões Assistência Técnica
PHILCO	TP20V56	Dark screen with normal sounding characters	Dz-701 shorted next to flyback	Replace it for another like it	ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE
PHILCO	PH32M2	After a while on, the image goes out if you change channels, it comes back for a while again	Ca8-ca15-ca12 100/25	Replace of 3	MARCELIO DREISSIG
PHILCO	PH21M2 TUBO	TV doesn't turn on, nor does the LED light up. total stop	Tsound is food in primary, but not in secondary	Replace the power supply strw, then, ok. resolder everything to give the device more life.	MARCOS lIZZI Confresa, MT
PHILCO	PH21MSS	It turned on with everything normal, but nothing was tuned.	C832 electrolytic 1000uf by 25v stewed.	Replace the component. (edfersom)	EDFERSOM
PHILCO	PH40R86	Appears immediately and disappears and the screen stays on	Q22 (gt3401) mosfet canal p		HP ELETRONICA
PHILCO	PH28S63D	No image. audio only.	Cold solder on the inverter and bad contact on the con3 connector (back light).	To avoid return, I replaced the current of the LED bars. I placed another resistor in series with r119 (2r2 + 1r). the 129v voltage dropped to 125v, and the bus current was 124ma and dropped to 89ma.	Eletrônica R-Tec
PHILCO	PH32F33DG	Turns on and then turns off	Voltages ok boards ok, defect in an LED or one of the buses	I disconnected the red LED wire from the board connector and the TV turned on normally, strange but it worked
PHILCO	PH32F33DG	Turns it on, philco appears and turns it off	Tested power supply was ok, all voltages, leds ok, no visible damage to the boards	Side buttons corroded with rust along with the button plate. just replace the board or rebuild it with new buttons
PHILCO	PCM1446	LED blinking and won't turn on	C722 dry 470uf/16v	C722 dry 470μF/16v	MARCONES DE ARARIPINA-PE
PHILCO	PH32M4	The TV had a pink or reddish screen.	A jammer was made on the v-con board on the resistor (rd51) and the TV returned to working with the image correctly.	Mkps	Marciok mkps
PHILCO	PH24M LED A2	Doesn't start. Not even the LED lights up.	Power supply with low and pulsing 12v line, between 11.2v and 11.4v.	Solved solve	Eletrônica R-Tec
PHILCO	PTV32D12D	No image.	Connector on the back light is faulty.	I removed the rb840 inverter resistor (4r7). the measurements were 61.7v and 248ma and then it was 59.1v and 178ma. I made the replace to avoid return.	Eletrônica R-Tec
PHILCO	PTV43E60SN SERIE B	Does not turn on back light	Ci u81	Replace ci u81	central audio e video
PHILCO	PH24M LED A2	Doesn't start. Not even the LED lights up. totally dead.	Power supply. IC1 (LD7531A SMD). little regulator with 6 legs. I didn't find it new in my city. So, I scrapped it.		Eletrônica R-Tec