☰

Philco Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philco
Results: 4838
Make Model Symptom Problem Solution By
PHILCO TP 2052
No image, when you adjust skreem the image appears Place a filter capacitor parallel to the existing 22mf x 250v AGILDO ANDRADE
PHILCO PH40R86DSG
Burning the LEDs Power supply that feeds the LED buses with 67.5v. 1st replace the LEDs. 2nd lower the LED voltage from 67.5 to 60v. remove all resistors rw812, 805, 811, 825 (smd r300=3r) insert a 6r resistor the voltage will drop to 60.5v EvandoViana
PHILCO PH42M
TV turns off the image after 20 minutes. Transistor a19t - ao3401 - leaky (heating too much and turning off the 12v supply to the t-con. Replace said transistor. JHtron
PHILCO PH21MSS
Burning the r816a Transistor q802(5551) shorted Replace for the same Eletrônica Bastos
PHILCO PH39N91D
The league comes soon and then fills with stripes, the image disappears and is left with sound Change the smd cap on the v com board and go for the hug eletronica publisom egn
PHILCO PH39N91D
The league comes soon and then fills with stripes, disappearing the image, leaving only sound Change the smd cap on the v com board and go for the hug eletronica publisom egn
PHILCO PH21MSS
It doesn't turn on, the LED just keeps flashing Diode
PHILCO PH32UDSGW
LED bars do not light up, voltage is only 38 volts and does not rise to 65 volts to light them Faulty dp403 diode Even though it was ok, I replaced this diode and the LEDs came back on correctly. ser-mga
PHILCO PH43N91
Doesn't start. the standby LED doesn't even light up Missing 12v and 24v voltages, resistors (rw938,967, 952, 969, 970, 971, 972, 973) all blown Replace the resistors, everything solved CDS_DIAS
PHILCO LED PH28S86DG
Does not turn on standby Defect in the power supply two caps. electr. 330/35 Replace with 2 cap.470/50 sono show RNeletronica
PHILCO TP14U56
This TV arrived on standby and won't start After thorough research I found the 915 diode ref; 1n4531 I used the 1n4148 the TV worked normally Just run for a hug, good luck! CLIC
PHILCO PH21MSS
Power supply with 20v Rewrite the memory Rewrite the memory.. Daniel. .Mauriti CE
PHILCO TPF2130
Turn on and off When it disconnects horizontally from the deflector, it no longer turns off. Changing the horizontal capacitors (2 blue capacitors) Josimar
PHILCO PH40D10DSGW
Normal stand by power supply lit, when turned on the 12v power supply drops and does not turn on Dp401 diode shorted Just replace it and solve it Luiz videotek
PHILCO PH200N
It doesn't turn on, just the blue light stays on. Corrupted u3 Replace u3 or re-record Vander CDs de Quixadá CE
PHILCO PH21B
League oscillates without image screen off C 450 next fly back 681k 2 kv replace Replace and run to the crowd Laercio Gonçalves umuaramapr
PHILCO PH39F33DG
Sometimes the backlight turns on and then turns off, giving the impression that it is the LEDs, the image remains blinking Defect on the power supply board, power supply with less than 390v drops to 250v Remove the 307,308,309e310 smd registers, clean the glue and run to the hug Luiz videotek
PHILCO PH58E51D
Doesn't start Power supply has no voltages Replace the 10k r115 which is open and the ci u1 tea 1755t which is short circuited. Danubio
PHILCO PH32N62DG
The black light doesn't turn on Glue under the smd r95 resistor Take out the resistor, clean the glue from below and on the resistor board again. Rafael
PHILCO PH40E36DSGW
Turning off less than 10 minutes C111 Remove and only joy Marcos roberto