Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH39F33	Standby only	Cold soldering	In the primary power supply circuit	Tec Center
PHILCO	PH 14 ULTRA SLIM N35	Low 50v power supplys do not come out of stand by or via the remote control	Faulty function keys	Remove connector and short the key connector on the board (replace all keys)	KV ELETRÔNICA(MACEIÓ)
PHILCO	PH21 US A1	Image shaking, retrace lines appearing and the screen is low and does not adjust	Flyback with problem	Substituir flyback	Eletrônica Six2
PHILCO	PH21US A1	Image shaking, retrace lines appearing and the screen is low and does not adjust	Flyback with problem	Substituir flyback	Eletrônica Six2
PHILCO	2054	Dull	Zd 701 de 8,2v	Replace it and run for the hug	Eletrônica júnior-v. grande -MA
PHILCO	PH23F33D	Distorted hoarse sound after some TV is turned on	C603 1uf ceramic capacitor, you can place an electrolytic	Replace, it's close to d601 obs. very difficult to find because his name is far from the piece	Velk Dj
PHILCO	PH21SS	Vertical closed from half down	Diode vd564	Replacing the diode defect resolved thanks to electronics pt	Chicão pereira
PHILCO	PH39E53SG	Doesn't start	Regulator u203=tps54319	I took it from a scrap board and it was fine	joao bosco gomes
PHILCO	PH32U20	Doesn't even turn on the LED (12v power supply keeps pulsing)	Dp 202 smd diode that is below the open ffm107 power supply fet heatsink	Replace it in my case I put a fr104 replace it without measuring	orlando lott
PHILCO	PH29M SS	Turns on with stripes on top and turns off	C307 capacitor 100µf/35v		3R
PHILCO	PH21MSS	Stand by blinking, tries to turn on and fails	Capacitor c833 and c828 stoves	Replace of 2 parts	Hugo
PHILCO	PH42M30	Stand bye LED lights up dimly and doesn't turn on	Ci regulator 3.3v n805, measuring 2.5 volts	Replace	HP ELETRONICA
PHILCO	TPF2922	It doesn't turn on, the stand by LED keeps flashing,	Replace cap ,c927 ,2,2x100v e c943 10x100v		DJ PITUKA
PHILCO	PH42M61DSG	Turns on, the philco logo appears and then it gets stuck at the message "initializing, please wait..."	3.3v regulator (n105) changed with 1.7v only.	It appeared to be a software defect, but the nand memory had already been replaced and the defect continued.	MLTOLOI
PHILCO	21MSS	It turns on normally, when we press power the LED goes off, the screen flashes and returns to stand bay.	In my case it was the flyback leaking.	Swapped the flyback and the TV worked normally.	Rdo Antônio Acre
PHILCO	TPF2130	Image blurs and turns off after a few seconds	Rusty tube socket	Replace tube socket	Joao paulo
PHILCO	TV PH21SS	Horizontal with bands on the sides (6 to 7 cm, about 3 fingers).	Replace the rp551 and a regulated three-way power supply		SEVERINO G 20
PHILCO	PTV32D12D	Sound escaping or no audio. When I picked it up it already had no sound.	Open smd ca23 capacitor close to the audio i.c.	I put a 200nf taken from another board. the sound appeared again.	sammolacerda
PHILCO	TPF2940	It turned on normally but tsound was no white drizzle, it had normal characters and the sound of the channel but tsound was no image just this black screen.	In my case the fly-back burst and sparked everywsound, burning r714 and changing r724, leaving the c731 smd shorted which also opened r723 smd	Replace all the components mentioned good luck ass:edfesom	Edfesom
PHILCO	PH21C	It only turns on if the board heats up	Ic 801 just trace		Jr eletrônica