Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PME25 PME-25	When opening the door, the plate and fan rotate.	Main relay (smaller relay) tested the microswitches and high relay note: disconnecting all connectors from the PCI panel when opening the plate and fan will rotate as the relay controls it, keeping the light on.	Replaced relay and cleaned door keys. electrical diagram https://www.electronica-pt.com/esquema/microondas/philco-pme25-microondas-65741/	Pedrozo
PHILCO	2130	Vertical closed	R 708 e d 702 perto do flay back.		Tec. zidane
PHILCO	PH39U21DSGW	TV turns off after about 15s to 30s on	Flash memory	Software update from the philco website, place a pendrive formatted with the drives and turn on the TV, quickly: open the menu, options, software update (usb), volume - (yes), and the TV will go into update	Teclados e Cia
PHILCO	PH21C	Turns on normally, with a slightly stretched width, and turns off after a few minutes and giving 130v at the power supply while normal and 102v	Changed resistor r839 from 82k giving 102k, just changing it returned to normal.	Replaced resistor r839 from 82k giving 102k, just changing it returned to normal.	DJ PITUKA
PHILCO	PH21MSS	Turns on, tsound is no signal but tsound is no image even on the AV	After banging my head a lot I found the Q301 and Q401 defective	The replace of q301 and q401 and running into the hug	Eletronica Carlos Viseu-PA
PHILCO	PH14 D	The tsh does not oscillate, when connecting b+ 105v and it drops to 16v, q401 oscillates but q402 does not trigger.	Missing +12v for the t402, track oxidized by cockroaches	Retrace the trail.	GDP2
PHILCO	TV PH21M SS	The TV works normally but after a few minutes the image turns white with the screen full of retrace lines	Q802	Replace or q802	Sinailson furtado
PHILCO	PH19C LCD	Red led	D002 open, flashing	Replace both diodes as a precaution	OLIMPIO- WATEK
PHILCO	PH32U20DSWG	The original board was scorched caused by lightning, I bought a board and it had the following defect after the change, the TV turns off after 40 and 50 seconds	Software corrupted or incompatible with the screen, in this case I solved the problem by removing the memory from the old board and putting it in the new one.	Try updating the TV with original firmware, if the problem persists even after updating, remove the memory from the old board and place it on the new board.	Eletronica ALLFATV
PHILCO	PH42M61DSGW	Turns on the logo appears and turns off	Problems with the update. After carrying out the update procedure, the problem was resolved		Paulo Russo
PHILCO	PH39R25DSG	Turns on, then the image goes off and only the sound remains, with a flashlight you can see the image on the display.	Shorted LED bars, out of a total of 40 LEDs, 16 were shorted, brightness control MOSFET burned on the board, damaging the plastic protection above and below the power supply board!	Replace the shorted LEDs, or buy new bars! Replace the TF450 MOSFET (AOTF450L), replace it with a TF454 MOSFET, which despite its VDS being smaller, looks great!	Lucas
PHILCO	PH20U21D	Completely stopped	Cap.smd c736 was replaced which caused a short in the 12vts line		José delta line
PHILCO	TP2920	It doesn't turn on, nor does the LED light up, it only turns on if you resolder the power supply area or place a hot dryer in the power supply area.	Change without measuring, d915, d914, zd906,zd903,zd904, ic902 photocoupler, ic903 tl431 c943 and c927	Replace without measuring, d915, d914, zd906,zd903,zd904, ic902 photocoupler, ic903 tl431 c943 and c927	DJ PITUKA
PHILCO	PH58E30DSG	When turned on, it works normally, after a few minutes, the image is blurry/distorted in bright light scenes	Clean all ends of lvds cables and cover with silicone tape to prevent recurrence		Victor Paz
PHILCO	PH40E36DSGW	Doesn't start	12v power supply with +- 3v and 24v with +- 6v oscillating	Replace of qp3 npn in the secondary with gap between base and emitter.	Rogermk
PHILCO	PH39U21	TV with sound without image backlight on	Replacement smd diode position n204/n205 open diode (a8) equivalent if you can't find the original bav21, on the display's vcom board		wisst service
PHILCO	PH21 MSS	When you press the on button, the LED turns off and generates high voltage as if it were going to turn on but it doesn't, the LED comes back on.	Deflector coil		Cicero lima ELETRONICA LINE JATOBA MA
PHILCO	PH21M SS	Ledy lit when pressing the c+ key the power supply keeps blinking and the blinking ledy does not generate high voltage	From 803	Replace the c803 power supply capacitor	Sinailson furtado
PHILCO	PH200N	Clean and resolder.	U9 with bad contact.	Clean and resolder.	eletronica bianca ipira-ba
PHILCO	PH28863D LED	Standby LED turns on, when the power button is pressed the LED turns off and the screen goes dark	Burnt out panel led	Changing the bar or LED	Eletrônica Pauly