Philco Repair Tips

Search: philco
Results: 4840

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH20U21D	Completely stopped	Cap.smd c736 was replaced which caused a short in the 12vts line		José delta line
PHILCO	TP2920	It doesn't turn on, nor does the LED light up, it only turns on if you resolder the power supply area or place a hot dryer in the power supply area.	Change without measuring, d915, d914, zd906,zd903,zd904, ic902 photocoupler, ic903 tl431 c943 and c927	Replace without measuring, d915, d914, zd906,zd903,zd904, ic902 photocoupler, ic903 tl431 c943 and c927	DJ PITUKA
PHILCO	PH58E30DSG	When turned on, it works normally, after a few minutes, the image is blurry/distorted in bright light scenes	Clean all ends of lvds cables and cover with silicone tape to prevent recurrence		Victor Paz
PHILCO	PH40E36DSGW	Doesn't start	12v power supply with +- 3v and 24v with +- 6v oscillating	Replace of qp3 npn in the secondary with gap between base and emitter.	Rogermk
PHILCO	PH39U21	TV with sound without image backlight on	Replacement smd diode position n204/n205 open diode (a8) equivalent if you can't find the original bav21, on the display's vcom board		wisst service
PHILCO	PH21 MSS	When you press the on button, the LED turns off and generates high voltage as if it were going to turn on but it doesn't, the LED comes back on.	Deflector coil		Cicero lima ELETRONICA LINE JATOBA MA
PHILCO	PH21M SS	Ledy lit when pressing the c+ key the power supply keeps blinking and the blinking ledy does not generate high voltage	From 803	Replace the c803 power supply capacitor	Sinailson furtado
PHILCO	PH200N	Clean and resolder.	U9 with bad contact.	Clean and resolder.	eletronica bianca ipira-ba
PHILCO	PH28863D LED	Standby LED turns on, when the power button is pressed the LED turns off and the screen goes dark	Burnt out panel led	Changing the bar or LED	Eletrônica Pauly
PHILCO	PH39U20DSGW	Turn on then turn off	Software update	Software update	Gilberto Costa
PHILCO	PH21M SS	Vertical reduced at the top and with lines in the center of the screen at the bottom.	D301 broken. Note: it does not appear in the multimeter measurement.	Replace d301 and resoldering of the same sector. resistors r317, r3018, r319 and r320, all with poor soldering due to overheating. (As a test, I replaced the c.i. la78141 with the stv8172a (the latter, which was on another board of the same classis, but from another model), had a cushion effect. Tsoundfore, it is not a direct replacement).	R-Tec
PHILCO	PHT660N2	Doesn't start	Power supply turns on and standby LED turns on and off normally...	Diode d108 or d109 and d110 (overheats and opens), these on the main PCI board.	Jair Ipumirim-SC
PHILCO	PHT-660N2	Doesn't start	Power supply turns on and standby LED turns on and off normally...	Diode d108 or d109 and d110 (overheats and opens), these on the main PCI board.	Jair Ipumirim-SC
PHILCO	PH40D10DSGW	Doesn't start	Diode dp202 primary power supply		BEIVIDAS SERVICE
PHILCO	PB126	Doesn't start	Broken trails	Tracks 7 and 8 on the mode switch board	Robert Jr
PHILCO	PH42 LED A	Does not turn on and no standby.	Bicolor LED of the faulty sensor.	Replace for another.	Jadson G Nascimento
PHILCO	PH21MSS	No sound with a hiss from the speakers and a low hum	Change the c205 capacitor on the computer and run to another	Electronics santana luís eduardo bahia	Crispiniano tec
PHILCO	PH42LED A2	The stanby led comes on, it turns on but nothing appears, after testing the power supply and the back-light, putting 3.3v on the pins - pon, pdim, blon, the screen has to light up, then you remove the lvds cable from the tcon, then the screen will light up indicating a defect,	C201 or c202 on t-con.- remove and go for the hug	C201 or c202 on t-con.- remove and go for the hug
PHILCO	TPF-2922	Dark image	Dz701	Replace	eletronica bianca ipira-ba
PHILCO	PH29MSS	Image pad and colorful stripes on and off	D811 with leaks changes and goes for the hug	Replace for 1n4007 or the original fr104	Rafael