Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH21MSS	This TV arrived at the store with the fly broken, I removed one from a board I had and put it in, but the TV turned on with a reduced picture.	New fly back and solved the problem		Eletrônica Renascer
PHILCO	PB121 BT	On standby - does not turn on	Transistor BD882 open base/collector	Replace the same.	Maastec
PHILCO	PCM2044, 2046	No characters	Zener zd601 shorted or r613 open	Tv without characters and after changing, tda 8361, or vertical ci (which could cause the problem, I came across zener 8v2 (zd601) in parallel with r613. problem solved.	cesar
PHILCO	TPF2130	LED is on but won't turn on	Bad 2408 memory Just change it and it kills all the voltage coming from the power supply so it won't turn on.		ELETRÔNICA SOUZA
PHILCO	PH19C	Só led st by	Diodo d2 pci principal
PHILCO	PH32 LED A2	LED goes off but tsound is no image or sound, sometimes it turns on and works indefinitely	When heating the memory with the blower, it worked in several attempts, it seems that when it cooled down it stopped working	Changing the 25q64 memory and ceramic capacitor on pin 8	davi.sls
PHILCO	PH29T21	Red led stb access. but doesn't call 8817	Regulator 802 smd short replace without measuring 8817	Replace u 802	MARCOS MELO. CEARA
PHILCO	PH39F33DSG	Turns on normally for a few moments and turns off the black light, looking like burned out LEDs	Defect on the power supply board u201 viper 17h = l = similar		MACSOM
PHILCO	PH21B	Off, when plugged in, the LED flashes, the power starts to generate and dies, then all you have to do is unload the caps.	Transistor v553 2sc1815	To replace	gdp2
PHILCO	PH-24M LED	Without audio - 12v voltage, drops to 6.5v	Q3, (fet ao3401 smd) shorted or with changes.	Replace - for a new one preferably.	Severino Silva
PHILCO	PH21SS	The LED is blinking, and tsound are no voltages on the power supply's secondary, with only 34 volts on the +b.	819 diode near shorted transformer	Replace it, in my case it was just him and the TV returned to normal..	Rafael
PHILCO	PH51U20PSGW	Doesn't start, doesn't do anything.	Without the 5 volts of standby, nor of the ps_on. (in this case the ps_on has 5v).	Diode d901, q308 and q309 replaced.	Josiano
PHILCO	PH21M SS	List on screen vertical top and bottom	Resistor r816a 390r e o r818 820r		DJ PITUKA
PHILCO	PH21M SS	The image appears on and off, but sometimes it doesn't even appear, it just turns on and off and the LED keeps blinking	Replace without measuring q802 2n5551 and d819 1n4001	Replace without measuring q802 2n5551 and d819 1n4001	DJ PITUKA
PHILCO	PH32D	Plugs it into the socket, the standby light comes on, after several times, it turns on and off.	C14 47uf/35v (fsp180-4h02)	Replace capacitor	fabiosilvar
PHILCO	PHT1500 BLUETOOTH	After changing the battery it doesn't turn on anymore	Tsound is a switching transistor on the +12v line of the battery that "cuts" the power supply when disconnecting the battery or when it completely discharges. This is to provide assistance for assistance.	With the button on, and with a new battery installed, make a short between pins 1 (pin wsound the component is soldered on the board) with pin 3 of q21a which appears to be a triac. wire, don't solder. It happened to me, I hope I helped.	ASTEP-ASSISTÊNCIA TÉCNICA PESSOAL
PHILCO	TVPH24M LED	Turns on normally, after a few seconds or minutes the screen goes off, and the standby LED comes on, along with the voltages on the cable that goes to the screen LEDs, drop from almost 70v to 12v	1 LED on the screen burned out and as it was in series, it left another 9 LEDs, off, a jumper was made and it was ok and it never turned off again. You can also notice when the screen is on if tsound is a dark spot, then it is a burnt LED sign		Rodrigo Coelho
PHILCO	PH39E53SG	The TV turns on, the LEDs turn on and then turns off, leaving the image in the background and the sound.	In my case tsound was a burned out LED on the bar. To test without opening the panel, measure the LED returns, the LED bar has 8 returns, measure from n1 to n8 if one of them gives a different voltage from the other, the LED is open or shorted.	Removing transistor Q3 on the inverter board removes the protection and the LEDs remain on, but the correct option is to open the panel and replace the burnt LED or replace the entire bar. (hugs, we will post more tips tsound technical friends)	PRO PC ELETRÔNICA E INFORMÁTICA
PHILCO	PH21M SS	Does not turn on, LED is on, when you press power, the LED flashes, +b with 20v	Child lock activated	Turn on the TV with the remote control, go to the menu and deactivate the child lock. hugs to everyone!!	Adrian Chapadão do Céu-Goias
PHILCO	PCM 1446 E 2046	No characters	Check c612, c175, r614, r613, zd601	Replace	Mauro Mascarenha Tel.( 88 )981422821 Parazinho - Ceara