Philco Repair Tips

Search: philco
Results: 4840

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH42M30	Stand bye LED lights up dimly and doesn't turn on	Ci regulator 3.3v n805, measuring 2.5 volts	Replace	HP ELETRONICA
PHILCO	TPF2922	It doesn't turn on, the stand by LED keeps flashing,	Replace cap ,c927 ,2,2x100v e c943 10x100v		DJ PITUKA
PHILCO	PH42M61DSG	Turns on, the philco logo appears and then it gets stuck at the message "initializing, please wait..."	3.3v regulator (n105) changed with 1.7v only.	It appeared to be a software defect, but the nand memory had already been replaced and the defect continued.	MLTOLOI
PHILCO	21MSS	It turns on normally, when we press power the LED goes off, the screen flashes and returns to stand bay.	In my case it was the flyback leaking.	Swapped the flyback and the TV worked normally.	Rdo Antônio Acre
PHILCO	TPF2130	Image blurs and turns off after a few seconds	Rusty tube socket	Replace tube socket	Joao paulo
PHILCO	TV PH21SS	Horizontal with bands on the sides (6 to 7 cm, about 3 fingers).	Replace the rp551 and a regulated three-way power supply		SEVERINO G 20
PHILCO	PTV32D12D	Sound escaping or no audio. When I picked it up it already had no sound.	Open smd ca23 capacitor close to the audio i.c.	I put a 200nf taken from another board. the sound appeared again.	sammolacerda
PHILCO	TPF2940	It turned on normally but tsound was no white drizzle, it had normal characters and the sound of the channel but tsound was no image just this black screen.	In my case the fly-back burst and sparked everywsound, burning r714 and changing r724, leaving the c731 smd shorted which also opened r723 smd	Replace all the components mentioned good luck ass:edfesom	Edfesom
PHILCO	PH21C	It only turns on if the board heats up	Ic 801 just trace		Jr eletrônica
PHILCO	TP2010	TV turns on with a vertical line in the middle of the screen and turns off and the LED blinks	R709 amended	R709 amended	Eletronica Line Jatoba ma-org-Cicero l
PHILCO	PH14 ULTRA SLIM	Goes into protection with noise in the flyback	C450 marked 681 (680pf)	Replace	Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821
PHILCO	PH200	Does not turn on secondary dead	In my case it was the audio output	Replace everything	eletronica sto ant rj bahia
PHILCO	PH42M61	Só stand by	N805 regulator (near the processor) just change it, I mean in my case it was it and I hope it's yours too.		Bruno Nicácio
PHILCO	PH29USA2	Screen with colors shuffled like a rainbow	Ptc of the kinescope magnetizer defective.	After changing the ptc, the perfect image returned to normal.	Everton Moscato
PHILCO	PH14C 20C	Sound 0 mute 1 full volume.	After copying several memories, it can only be resolved by changing the data.	Menu 6483, mute, up to m2, setup celect to 1, mute up to m6, v. max from 46 to 63, mute m9, balance from off to on. sir stand by	George Pontes
PHILCO	TP2920	It connects with the magnetized tube and has a colored wheel in the middle of the screen.	Rl1	Replace the rl1 relay	Sinailson furtado
PHILCO	TP2920	Turns on with retrace lines at the top of the screen and the vertical closes and the TV turns off.	C1	Replace o capacitor c1 100μF25v	Sinailson furtado
PHILCO	PH21USA1	Low noise at the power supply, all low power supplys, +b 60 and a few v. does not start.	R 553 from 5k6 altered for 13k .trimpot 2k aberto	Replace these components.	J B Eletron
PHILCO	PH21MSS	League. no signal and when you put in the antenna cable everything goes dark	Ci memory	Defective memory ic. just run for the hug	Eduardo santos
PHILCO	PH32M3 LTA320AN01	Turns on, shows the logo and turns off the backlight, leaving only the sound and the image in the background without light.	Strong burning smell, I opened the screen and found that tsound was a light bulb sparkling.	The lamp connector was sparking. I replaced it and it resolved. Tip for everyone: when disassembling LCD TVs, keep the lamp connectors ;)	PL Eletrônica