Philco Repair Tips
Search: philco
Results: 4838
Results: 4838
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PH40R86DSGW
|
No image, only sound | In this case, tsound is no point in changing any burned-out LEDs, you have to change all the LED bars, because even when they are turned on, all the LEDs are changed and go out. | After the replace resolved | PATRICK ELETRONICA |
| PHILCO |
TP2054
|
With sound and menu without image | R723 (4k7) smd na linha do abl | I replaced it and it went back to normal | Emanuel (Alfa Eletronica) |
| PHILCO |
PH21B
|
Turning off with noise from the speaker | V502 | ||
| PHILCO |
PH48S61DGH
|
LEDs came on and then went out | I removed the 5.6k 766 resistor. and everything was fine | Adalton ms vigia | |
| PHILCO |
TP-2053S
|
Does not turn on standby, keeps blinking | Era o flyback | Flyback short switch | Gilson Paulistana |
| PHILCO |
PH39E53SG
|
Flickering image | On the screen ruler, remove r851 and jam it, it is next to c812 and also next to u801 | badri eletronica <small> |
|
| PHILCO |
PH24M-LCD
|
TV locked showing padlock, some remote control keys don't work | Eprom 24q16b | 24q16b eprom replacement | EDSON |
| PHILCO |
PH39R25DSG
|
Burned inverter mosfet TF450 in short (aotf450) difficult to find and very expensive. | I put a 7n65, it worked but got a little hot. LEDs lit up normally. | I replaced it with a 13n50 and it went back to normal. LED output voltage is +/- 140v. | Mau3000 |
| PHILCO |
TFP2130
|
TV turns on normally with a beautiful image, but the image has a flash or lightning in the image and very thin colored lines | C=607 shorten | Replace it with another and run to the hug | Antonio Carlos (Eletrônica Renascer) |
| PHILCO |
PH42M61
|
Call and "wait", sometimes it works, sometimes it doesn't. does not tune channels. sends hdmi inputs, for example, tv turns off. doing wrong functions. | Change the ci that generates a voltage of 3.3 v, close to the channel selector. | Replace 1117-33 | arock |
| PHILCO |
PH21MSS
|
It doesn't turn on, the standby LED comes on, I turn it on on the control, the LED goes off and doesn't turn on, the power supply goes to 60v and drops to 20v. and the LED is blinking | Change c847, c827, q802 and r845 as a jumper | DJ PITUKA | |
| PHILCO |
PH21SS
|
Does not tune the channel, with all voltages on the varicap | Replace r317 ,47k e r318 ,12k do lado do varicap. | DJ PITUKA | |
| RADIO PHILCO |
PH229N-USB
|
Fm doesn't pick up correctly | Diode diode d300 and 3001 shorted | julinho da eletronica | |
| PHILCO |
PH28D27
|
Every stop, no LED lights up | U905 burns due to a power outage, sometimes it burns, other times it doesn't burn and makes everything stop and just change it and go to the hug, it stays close to the coil l818 eup3 | eletronica publisom de natal | |
| PHILCO |
PH28D27
|
Every stop, no LED lights up | Change all the capacitors in the power supply and go to the hug | eletronica publisom de natal | |
| SEMP TOSHIBA PHILCO |
48L2400 PH48
|
No image white screen LED on | Cd17 | Shorted smd capacitor on t con plate | Adrian Chapadão do Céu Goiás |
| PHILCO |
PH42F10DSGWACVA
|
Restarting without stopping | Short in keyboard line | Smd capacitor position ck2, next to the processor, shorted | shermanflima |
| PHILCO |
PH21MSS
|
Turns on, image appears and turns off and the LED blinks | Replace resistor r816a 390r, r818 820r, cap c833, c835, c847, c826, q802 coloquei mpsa42 | DJ PITUKA | |
| PHILCO |
PH21MSS
|
Liter at the top of the screen by doubling the image | Capacitor 307 de 100µf/35v | Replace the same | Cassiano |
| PHILCO |
PH29USA2
|
LED lights up and slowly turns off | C406 100x25 sold out | Just replace | Paial.eletros |