Philco Repair Tips

Search: philco
Results: 4838

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH40D10DSGW	Does not turn on, completely stopped, without voltages on the power supply secondary.	Up201 causing short in zdp201 cp202.	Changing the up201, checking all nearby components.	Antony Garcez
PHILCO	PH21MSS	The screen full of line, vertical defect	Replace resistor r306, 220r		DJ PITUKA
PHILCO	PH40U16DSG	Sometimes it turns on, sometimes it doesn't, when it turns on the power LED turns off and returns to the stand bay again, sometimes it even shows the Philco logo and turns off	Change cp from the primary power supply, cp 105 cp 201 and cp 205 and run for the hug		Eletrônica Power saquaçú RJ
PHILCO	PH32U20DSGW	Burning leds	Change all the LEDs and remove rp411 rp433 from the circuit to reduce the voltage from 62 volts to 54 volts	Replace all the LEDs and remove rp411 rp433 from the circuit to reduce the voltage from 62 volts to 54 volts	antonio nobrega (patos pb)
PHILCO	PH32B51DSGW	The Philco logo appears then turns off and restarts	Update	Download from the Philco website which has the instructions.	Mariano
PHILCO	PH21B	+b of 110v = 61 to 80, without -14 and +14, it kept making a noise in the tragus or ci oscillating, cutting the secondary voltages	R 553 from 5.6k changed to 7.8k	Just replace	Marcleo
PHILCO	PH39F33	Red LED on but not turning on	I even replaced the ic u201 but it was not the cause of the problem.	On the power supply board, disconnect plug p1 (it is next to l201) and then connect the power socket. then unplug the socket and reconnect plug p1.	littlecarlos
PHILCO	PCS2976S	With vertical colored stripes	Obs r709 of 18r altered with low value causes this defect	Changing resistor can put 22r	jose joaquim
PHILCO	32E53SG MS63LA MAC2HG	TV arrived sound with faulty electronics, turns on the Philco logo and turns off, just tighten the screws on the power supply and run for the hug	Tighten the power supply screws		Raimundo
PHILCO	PH21C	When connecting the TV to the socket, the stand bay ledy turns on the power supply, the TV tries to assist by making a strange noise in the image tube, like frying and it does not generate high voltage.	Change the picture tube and the TV will work normally. God be praised!		Sinailson furtado
PHILCO	PH21M SS	Does not turn on, LED is on, and turns off but does not turn on, high supply with 159v	Change resistor r810, 15k next to the photocoupler.		DJ PITUKA
PHILCO	TPF2121C	Turns on and off with a black screen, difficulty turning on.	Change booster capacitor c715 .68, next to the horizontal transistor.		DJ PITUKA
PHILCO	TP2920	Colored line at the top of the screen	Replace the two 6n8/2kv polyester capacitors		José
PHILCO	PH32M A3	The stand bay LED does not turn on, flashing intermittently, with a voltage of 5v and 12v on the missing power supply.	B1,aa,qa	Replace the photo coupled to the tl431 and the q33 which is the d478 mosfet and the TV will be working normally. God be praised!	Sinailson furtado
PHILCO	PH43C21P	It doesn't work, just the standby LED blinks. noise at the power supply.	Changing two 1000/10 capacitors in the cx820 and 821 power supply.		Danubio
PHILCO	TP-2054	Doesn't start	Fly-back	Replace fly-back ov2094d1 replacement jf0501-19192a	Sinailson furtado
PHILCO	PH32F33DG	Standby LED flashes continuously and does not turn on	Software defect on the main board and flash memory	Download software from the philco website, format pendrive, insert the 2 files on the pendrive, unplug the TV, insert the pendrive into the TV's USB, turn on the TV with the power button pressed until the software installation menu appears, the TV will reboot, then that's it. run to the hug	OSVALDO SEABRA
PHILCO	PH22B16D LED	Scans/squares/freezes on digital channels	I tried the tuner and it didn't solve the problem, but the defect was in the tuner's 3.3v supply.	Replace u001 3.3v regulator with 2.8v....	MIGUELTV
PHILCO	PH39U21DSGW	After pressing the power button, the TV turns off in a few seconds. +or - 40 sec	Corrupted memory	Update memory	Bili
PHILCO	PH40E36DSGW	Turning off in less than 10 minutes. You have to wait a few minutes to be able to turn it back on again. however, it starts to turn off more and more quickly.	Removed capacitor c111 smd. It is between the processor and the flat. close to q8 and d5. which connects the 5v standby line. (tip from Robert, right sound on the website. However, the location of the capacitor was defective. I'm replacing the tip to make it easier to find it.)	I replaced it and it resolved.	Eletrônica R-Tec