Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem	Solution	By
PHILCO	TP2010	TV turns on with a vertical line in the middle of the screen and turns off and the LED blinks	R709 amended	R709 amended	Eletronica Line Jatoba ma-org-Cicero l
PHILCO	PH14 ULTRA SLIM	Goes into protection with noise in the flyback	C450 marked 681 (680pf)	Replace	Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821
PHILCO	PH200	Does not turn on secondary dead	In my case it was the audio output	Replace everything	eletronica sto ant rj bahia
PHILCO	PH42M61	Só stand by	N805 regulator (near the processor) just change it, I mean in my case it was it and I hope it's yours too.		Bruno Nicácio
PHILCO	PH29USA2	Screen with colors shuffled like a rainbow	Ptc of the kinescope magnetizer defective.	After changing the ptc, the perfect image returned to normal.	Everton Moscato
PHILCO	PH14C 20C	Sound 0 mute 1 full volume.	After copying several memories, it can only be resolved by changing the data.	Menu 6483, mute, up to m2, setup celect to 1, mute up to m6, v. max from 46 to 63, mute m9, balance from off to on. sir stand by	George Pontes
PHILCO	TP2920	It connects with the magnetized tube and has a colored wheel in the middle of the screen.	Rl1	Replace the rl1 relay	Sinailson furtado
PHILCO	TP2920	Turns on with retrace lines at the top of the screen and the vertical closes and the TV turns off.	C1	Replace o capacitor c1 100μF25v	Sinailson furtado
PHILCO	PH21USA1	Low noise at the power supply, all low power supplys, +b 60 and a few v. does not start.	R 553 from 5k6 altered for 13k .trimpot 2k aberto	Replace these components.	J B Eletron
PHILCO	PH21MSS	League. no signal and when you put in the antenna cable everything goes dark	Ci memory	Defective memory ic. just run for the hug	Eduardo santos
PHILCO	PH32M3 LTA320AN01	Turns on, shows the logo and turns off the backlight, leaving only the sound and the image in the background without light.	Strong burning smell, I opened the screen and found that tsound was a light bulb sparkling.	The lamp connector was sparking. I replaced it and it resolved. Tip for everyone: when disassembling LCD TVs, keep the lamp connectors ;)	PL Eletrônica
DVD PHILCO	PH154	Turns on and blows fuse immediately	After checking the rectifier bridge I discovered that it was the ci u1 on the board, I just changed it and ran to dim dim		ELETRONICA PUBLISOM DE NATAL RGN
PHILCO	PH23F33D	Sound failing. After several minutes, tsound is no sound.	C602.		jr_TEC
PHILCO	MSS MSS	With normal image only at the bottom - everything is dark above	Causing the electro capacitor - 303 of 470.uf - close to the vertical ci-	Just replace and move on to another cucumber - resonant electronics claudia mt-	Raimundo damascena
PHILCO	TP2920	Inoperative standby LED does not turn on	Ic901	When placing the finger on the IC901, the power supply activates and the stand bay LED lights up. Just replace the ic901 and the TV will work normally. God be praised!	Sinailson furtado
PHILCO	TP2920	Normal turns on the menu characters appear as normal but the image does not appear and the screen remains dark.	A rabble	Replace the 4k7 r723 and the TV will work normally. God be praised!	Sinailson furtado
PHILCO	PH800M DM1001-SE.PCB	Turns on, but no sound, normal outputs. (tda7498e)	Electrolytic capacitor ce37(47uf/50v) shorted activating mute circuit.		MLTOLOI
PHILCO	PH200	Sometimes it turns on with a flashing display or just a blue LED on volume	Lack of 3v3 in the supply measure pin 8 eeprom if it is low the defect is tsound	3v3 regulator	beto2828
PHILCO	PH32E31DG	No image after a while on	R2b0 20k changed	Put 22k go for the hug	PS eletrônica
PHILCO	PH24D20DG	The TV turns on, no image appears and returns to stand by	12v zener on the screen ruler, it is after the fuse		Mariano