Search: philco
Results: 4838
Make Model Symptom Problem Solution By
PHILCO PH21US A1
Turning off Transistor v502 e capacitor c580 3R
PHILCO PH21M2 SS
PH08K-C01
Horizontal bar, image folded horizontally Zd483 (9.1v) RICHARDO SILVA
PHILCO PH24D20DM2
SW10
Turns on but no image Q813 on main board open Replace him barbadinha
PHILCO PH21MSS
Image stretched horizontally Replace diode d454 fr104 next to the deflector connector DJ PITUKA
PHILCO PH32E31DG
Restarting, as if it needed to be updated On/off switch (joystick) Krul
PHILCO PH22S31
Does not turn on standby Changing the photo coupler and the 431 on the side RMSELETRONICA
PHILCO PH1100M
It starts hello and sometimes it just stays LED STBY Ce 5,ce6,ce2,ce8,ce7,all change 100mf 16v put 470mf,it is located near the connection with the power supply on the main board, it feeds 5v,vcc pin,check the 1,2 and 3v smd regulators AF-SAT Eletronica
PHILCO PH21 US A1
It turns on with the image shaking and the TV speaks and then the voice disappears. Shhha Replace the capacitor c507a and just run to the hug. Sinailson furtado
PHILCO PH20U21D LED
Does not work without voltages in the secondary Cap smd723 Replaced eletroberger
PHILCO PH28S63D
Sound failing when increasing Smd transistor q3. on the main board. 12 volts from the audio ci keeps oscillating. Ozatec electronica sarandi / pr 12/23/2019 OZATEC ELETRONICA SARANDI / PR
PHILCO PH49F30D
Does not light backlight Vw10 or vw09 shorted diode. Replace Hndrsn
PHILCO PH21M
Working, but with a buzzing sound in the power supply transformer, sounding like a cricket. D-802 as leak. SANTANA
PHILCO PH28T35DG
TV turns off after a while of use, intermittent sometimes D201 The audio ci was getting hotter than normal at low volume, I threw heat on it with the blower and the TV turned off immediately, I replaced the d201 which looks like a transistor and it went back to normal. AlanCocteau
PHILCO PH28T35DG
TV turns off after a while of use, intermittent sometimes U501 The audio ci was getting hotter than normal at low volume, I threw heat on it with the blower and the TV turned off immediately, I replaced it and it went back to normal. AlanCocteau
PHILCO PH21US A1
It doesn't turn on, the stanby LED is flashing and the power supply has 56v on the secondary Change resistor r514 36k, next to the regulator strw DJ PITUKA
PHILCO PH21SS
Carbonized components r448, c437,vd435,c450 Change the r448 of 22k c437 of 471k for 2kv the vd435 in place of this diode works a capacitor of 471k for 2kv also change the capacitor 450 of 681k for 2kv 2kv, the vd435 instead of this diode works a capacitor of 471k by 2kv also replace the capacitor 450 of 681k by 2kv Sinailson furtado
PHILCO PH21SS
Don't turn on the power supply mocking R470 e o vd435 Replace the 1r2 r470 that sends 130 volts to the +b and also replace the 471k polyester capacitor for 2kv that will be in place of the vd435 diode and then just run for the hug. Sinailson furtado
PHILCO PH24D20DG
Inoperative led off Grgulador ear To replace CARLOS ELETRONICA
PHILCO PH32S61DG
No image, dark screen, backlight off Vd752 = sb2200 Vd752 = sb2200, an sb3200 diode was placed in place, it is close to the LED connector. silnei
PHILCO PH32D
Plugs it into the socket, the green LED lights up, changes to red and does not turn on C14 = 47mf x 35v on the defective power supply board Replace capacitor silnei