Philco Repair Tips
Search: philco
Results: 4811
Results: 4811
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PH21D
|
Doesn't start... only after insisting a lot | Cp 881 47uf 25v i cp4u7 50v next to the vertical output..both with high esr | José técnico | |
| PHILCO |
2051
|
TV inoperative stand-by LED off and a beep on the traffic. | In my case, a high leak caused the horizontal to short out. and the vertical was damaged, which also charred the r 605 (33 r) | Patch or replace the fly-back and replace the vertical (tda8356) and the r 605. | Edfesom |
| PHILCO |
PH21M-SS
VER.B |
R-816 from 150r toast when changing it smoked | Q-802 shorted | Changing the r-816 r-818 and q-802 worked perfect | ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE |
| PHILCO |
PH21B
|
Vertical closed and shutting down | Shorted varicap | I released the 5v. the TV worked | Robenilsom |
| PHILCO |
PH21SS
|
Horizontal closed on the sides around 5 to 6cm on each side | L441, close to horizontal with magnet | Edson Gomes | |
| PHILCO |
PH32
PH3220 |
No image back light on | Tcom connection with burnt out display | The only way is to replace the entire display | Leandro leite |
| PHILCO |
PH21M SS
|
Turn on the image and turn off | C318 4.7micro dry electro cap is in the protect stage | Replacement | IRAN FORTALEZA |
| PHILCO |
PH21SS
|
Vertical with lines and buzz | C 562 | eletronica ph | |
| PHILCO |
PH21MSS
|
The LED doesn't even light up | D818 shorted | Claudia resonant electronics - mt | Damascena Eletrônica ressonante |
| PHILCO |
PH21MSS
|
Heating and burning vertical outlet la78041 | CI voltage is +14 and -14 were tsound for 17v, the fight was bad lol | After changing the la78141, also mercilessly replace the r829 for a 150k one that regulates high voltages, and everything goes back to normal... | Max |
| PHILCO |
PH32U20DSGW LED
|
Red LED but it doesn't turn on | LED burnt out, just replace | Genario | |
| PHILCO |
PG21MSS
|
Does not turn on, LED off, power supply varying | Shorted 18v diode, close to zd804 | Hiago correia | |
| PHILCO |
PH24B
|
Triplicate image | Eepron | Try service mode-(contrast menu 9735) config id cmo-m236h1, if it doesn't work rewrite eepron | CENTER SOM |
| PHILCO |
PH14D
. |
Fast blinking led | R839 from 82k changed to 104k. precision resistor. green resistor. | Replace r839 from 82k. | <small> |
| PHILCO |
TV PH21M SS
|
Turn on the image with about four fingers on the screen to download it and then turn it off | After measurements I found two altered resistors, a 1.8r resistor, one giving 53r and the other giving 2.2r. | (replace both r319 and r320 with 1.8r) | Eletrônica Bastos |
| PHILCO |
PH29E52DG
|
The TV turns on, the Philco logo does not appear, the sound is normal. | The power supply on the CN400 connector of the LEDs was checked, it was 57 volts and it was found that one of the busbars was burned. 3v LED. | The burnt LED was replaced and the device started working normally again, operating voltage of the LED bus, 44 volts. | Adriano Miranda |
| PHILCO |
PH42M61DSGW
|
Weak red led | Low supply short nos smd ld1117s33 | For 1117 saa | rogeriofederal |
| PHILCO |
KH111F 1.6
|
Turning off in a few minutes | V502 close to ptc | V502 2sc2383 I couldn't find it on the market so I replaced it with 2sc2655 | Fábio |
| PHILCO |
PH29T21D
|
Works and turns off | Keyboard board with shorted keys | omegaomega | |
| PHILCO |
PH21SS
|
TV does not turn on, no stand by, power supply disarms when turned on | Optocoupler replacement | Emerson |