Philips Repair Tips

Search: philips
Results: 14206

Make	Model	Symptom	Problem	Solution	By
PHILIPS	29PT 5642	Horizontal output is shorted	C 2460 470/16		Leal
PHILIPS	21PT9467	Image disappears (turns dark) as it heats up	Replace q507 kinescope board		NV ELETRONICA/VALDEMIR
PHILIPS	29PT4635	Overheating the horizontal transistor and it doesn't work	Flyback	Replace	ELETROCLAUDIO DE AGUAS BELAS PE
PHILIPS	29PT552A	Does not oscillate	C2551 not secondary		fabiusmax
PHILIPS	14PT110A	Does not turn on, just stays on standby	C2448 and c2551 of 47uf 160v	Replace	ELETROCLAUDIO DE AGUAS BELAS PE
PHILIPS	28PW6005/01 A10E	Tsound is no sound, no av, the sound level does not work	No modulo bord 3139 123 5244.2	Non-ic solders 7301 (tda8885h)	joaquim cunha
PHILIPS	20PT3331	Vertical closing top when it gets hot	C2461 1n smd		Continental
PHILIPS	14GL1010	No focus/no image	Rusty tube socket	Replace the socket	eletronica nativa
PHILIPS	FW M35/19 MINI HI-FI	Optical unit did not light up or move	Diode d754 but it is good to measure the others that are next to it, it was open.		fabiusmax
PHILIPS	14GL1316 1316	Does not tune channels	Normal voltage and characters change t7100 with leakage	Resolved	ELETRO LUIS
PHILIPS	20GL 1040	Totally inoperative	C508 680pf-3kv with internal spark	Resolved	ELETRO LUIS
PHILIPS	MX2600	T locke d	Locked tray	Press the sweat key for 2 seconds and then play with the CD in the compartment	VITALTEC
PHILIPS	29PT4635	Defect, shiny stripe from top to bottom on the side	When changing the famous bc 337 and 327 together with the 47mf/25 capacitor and this shiny strip appears on the side, simply add a 1k/100v capacitor between the base and emitter of the bc337 or between collector and emitter	Due to the poor quality of the bds of life (in case you want to put a stronger one as it heats up the bcs a lot) even if you add the capacitor it still appears like this, in this case keep the bcs	José Gusmão
PHILIPS	DVD DVP-630/02	Led power, pisca	Power supply c316		Ernesto Figueiredo
PHILIPS	29PT4635 L01.1L	Lately, whenever I change the 2 silver bc(337/327) and put bd in its place, horizontal bands have appeared on the sides with drizzle	It's the bds in life usually with non-standard hfe that cause this	As I haven't found good quality bds, I've already tried 3 manμFacturers, I'm returning with the bc ones and the atv no longer has the track	José gusmão
PHILIPS	29PT4635 L01.1L	When activating the power key it remained on standby and the LED accessed but activated the channel or on the control itself, the LED turned off but turned on	Q7461 and q7463 were broken when changing them, it continued without turning on, they receive 13 volt voltage from 2 places of the power supply and the flyback after it started working, I noticed that r3493 of 6.8Ω was toast, when changing it I verified that only Tsound was voltage at the power supply output (main aux.) but it didn't reach the transistors following the line I found an SMD diode leaking d6464 when changing it the TV started working normally again		José Gusmão
PHILIPS	PT	When it turns on, the three horizontal RGB lines appear (green, blue and red). Afterwards, the normal image appears and turns off.	C-2460	Can put 104k, 104j, 663k 250v	maximuz
PHILIPS	29PT4635	Burning the horizontal outlet	Resolved after changing the output and the c2455, we found that the c 2455 47mf was ok in the test, but with an oscillograph it showed a big difference in the waveform between its two ends, we changed it and solved the defect.		bf.colatino
PHILIPS	14PT3131	Does not turn on normal power supply	Chap. smd connected to the rear emitter. smd 7423 short		ELETROCLAUDIO AGUAS BELAS
PHILIPS	14PT3131	Doesn't start	Chap. smd connected to the rear emitter. smd 7423 hundred short		ELETROCLAUDIO AGUAS BELAS