Philips Repair Tips
Search: philips
Results: 14206
Results: 14206
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
32PF9996 /78
|
Always connects to the same channel. | This is one of the features of hotel mode, the TV always turns on the same channel and at the same volume. to confirm, enter the code 3-1-9-7-5-3-mute, choose the first option in the hotel mode menu "hotel mode", if it is yes, change it to no, then press the cursor [arrow down ] until the "memorize" option is ok. | Silva | |
| PHILIPS |
32PF9996 /78
|
Indicating f or cf on the screen (factory mode active). | Press the [volume - (minus)] key on the TV for 5 seconds and turn the device back on. | Silva | |
| PHILIPS |
32PF9996 /78
|
Ambilight doesn't work, it stays off. | Check "aci" power supply panel | Silva | |
| PHILIPS |
32PF5320 /28
|
Dark screen. | If this symptom only occurs on the RGB/CVI input, try adding a 150PF capacitor in parallel with the 2E09 capacitor on the SSB panel. | Silva | |
| PHILIPS |
32PF5320 /28
|
No sound. (with or without image for TV, VCR, DVD). | If the speaker is open, after the replacement it is necessary to correct the memory data (nvm) by executing the sequence below: 1 - select the tv in av1; 2 - sequentially type 0 6 2 5 9 6 status/exit; this way the TV will enter service mode showing the information below: 0000xx lc4yxxxxxxxx - indicates the version of the software used err 0 0 0 0 0 0 0 - indicates if tsound was an "error" indicating a failure in the product. clearoptionstunerwhite toneaudio>nvm editor 3 - with the cursor keys (down arrow), navigate to the nvm editor option. (attention: tsound is also the sc editor which should not be changed); 4 - with the arrow to the right, enter nvm editor mode and the following submenu should appear: hex decadr 0x000000 000val store 5 - adjust address values according to the table below: location names address dec value dec hex nvm pre btsc st 86 11 0b nvm pre fmm bgdkm 89 11 0b nvm pre sap 91 11 0b nvm pre extav 93 15 0f nvm volmax end 110 105 69 8 - with the cursor key (down arrow), select store; store to exit, press the status/exit power off key to reset the TV. | Silva | |
| PHILIPS |
32PF5320 /28
|
No sound. (with or without image for TV, VCR, DVD). | In hdmi, with remote control press "i-ii" key | Silva | |
| PHILIPS |
32PF5320 /28
|
Intermittent mute (sound or image). | Change the following items in each of these inputs: signal input y resistor (3q06 and 3r22) from 75r to 120r; input vga resistor (3q06) is close to coils 5q06 and 5q11; cvi input (cinch) resistor (3r22) next to the 6r63 and 6r64 smd diode next to the tuner. | Silva | |
| PHILIPS |
32PF5320 /28
|
Indicating f or cf on the screen (factory mode active). | Press the [volume "-" & program "-"] keys simultaneously on the TV for 5 seconds. | Silva | |
| PHILIPS |
32PF5320 /28
|
Damage fuse | This item depends on the chassis and LCD display used, if the power supply uses the gbj6j-b15 rectifier bridge (generally positions 6807 or 6h07) and it shorts out, it must be replaced by the ts6b05g-06 rectifier bridge with code 3104 307 09981. | Silva | |
| PHILIPS |
32PF5320 /28
|
After a while the image disappears. | - when connected to the video component input (dvd from other manufacturers and mx3910) 1) replace the coil is 5q06 which is close to the db15 connector (blue) of the ssb with a 100r resistor (currently used) this value can be reduced to a minimum value (jump). 2) if the result is not satisfactory, the "scaler software" must be updated using the gprobe/genesis program (contact technical support). | Silva | |
| PHILIPS |
15PF9936 17PF9945 23PF9945
|
White dots aligned on the display | Remover capacitor smd 2380 do painel scaler | Silva | |
| PHILIPS |
15PF9936 17PF9945 23PF9945
|
Doesn't work | Check capacitors c32 and c48 | Silva | |
| PHILIPS |
30PF9946D/78
|
Noise in the image via the hdmi or cvi input | Check soldering ic u4201 on ssb panel | Silva | |
| PHILIPS |
30PF9946D/78
|
Noise in the image via the hdmi or cvi input | Check welding connector 1601 on the ssb panel | Silva | |
| PHILIPS |
26PFL3404 /78
|
Remote control does not work | Check welding fb02 (panel ir) and fb205 (panel ssb) | Silva | |
| PHILIPS |
26PFL3404 /78
|
Interference when connected to hdmi | Check welds on: r1501, r4404, rp4404, rp4406 | Silva | |
| PHILIPS |
26PFL3404 /78
|
One of the colors in cvi is missing or has an irregular color | Cold welding ci u4201 | Silva | |
| PHILIPS |
26PFL3404 /78
|
One of the colors in cvi is missing or has an irregular color | Cold welding c1206 | Silva | |
| PHILIPS |
26PFL3404 /78
|
One of the colors in cvi is missing or has an irregular color | Cold solder r1203 | Silva | |
| PHILIPS |
26PFL3404 /78
|
Partially illuminated display | Possible leak in transformer t803, q801 and q802 - ipb | Silva |