Philips Repair Tips
Search: philips
Results: 14208
Results: 14208
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
20PT3331
|
Normal power supplys TV turns on and the screen does not light up (kinescope with filament off) then goes into protection mode | Resistors 3343 and 3344 | WAGGUINHO | |
| PHILIPS |
29PT4635/78
29PT4635/78 |
The bu 808 keeps burning in the fountains | I don't know | marcos | |
| PHILIPS |
21PT8467
|
With characters and one hundred luminance | R 3442 of 100k open on the abl line | ||
| PHILIPS |
29PT6566
L04.LAA |
Black band on the left side (08 cm) (lack of width on the left side of the screen) | C-2486 | I replaced the c-2486 everything went back to normal | Rogermons |
| PHILIPS |
20PT3331
|
The filament turns on and off 3 times and remains off | Q 7491 smd | Dj carlinhos | |
| PHILIPS |
21PT5433
|
Low sound (very low) | Swap c2444 470/16v | Beto Eletronica | |
| PHILIPS |
PT3336
L03.6L |
Vertical stroke and turned off | R 3448 | juci | |
| PHILIPS |
20PT 3331/78
|
No sound when turning on the TV after some time, the sound returns but is low. normal image. | Changed the c 2444 capacitor with low capacitance. This capacitor is close to the fly bak, for those who don't have the schematic. OK. | jaironuness | |
| PHILIPS |
29PT4641
|
Does not turn on, and the stand-by LED does not light up | Change coupler photo | ||
| PHILIPS |
20PT4331
|
Vertical beam | 7466,7464 7463, the 7464 was shorted but the protection did not activate, after replacing it went into protection due to the 7466 and 7463 | Dj carlinhos | |
| PHILIPS |
20PT4331/78R
|
Turns on the TV, horizontal RGB lines appear, vertical lines are slightly closed and then turns off. | Capacitor 2460 (663k 250v) | Edson Peixoto | |
| PHILIPS |
21PT5433/78R
|
Burning horizontal output - intermittent | Get straight to the point. Replace the deflector coil. case solved | Otecnico.20m.com | otecnico |
| TV PHILIPS |
20PT 120 A/ 78 R
|
TV doesn't turn on | 8444 leaky replacer. | jaironuness | |
| PHILIPS |
29PT4631
|
Serrated or sawtooth image | Changed resistor close to bc's 337/327 | Replace r3493/ 5r8 | cesar_unitec |
| PHILIPS |
20PT326A/78R
|
When turned on, it generates high voltage, the filament lights up, but it does not shine or sound, emitting a noise similar to a cricket. | Ic 7600 | The replace of the same | nonato |
| PHILIPS |
20PT326A/78R
|
Turns off when turned on, remaining on standby | Resistor 3470 18k open vertical protection | Replace of the same | nonato |
| PHILIPS |
29PT4640
|
When you turn it on, it turns off then, after insisting several times it works | Pre-horizontal filtering | Ronie Grein | |
| PHILIPS |
20PT3336/78
|
Normal OSD, dark screen and sound on the channels | R 3459 and r 3442 open (both 100k) | ELETRONICA ESTUDIER | |
| PHILIPS |
14PT1556
S L01.2E AA |
No image. Tsound is no brightness/contrast control, adjusting voltage doesn't help either. | Tsound is no information eht. resistance 3431 at output 8 of the tr.linhas (ehtinfo) burned out. | Raúl Faustino | |
| PHILIPS |
29GX1895
ANUBIS |
The image keeps shaking, tsound are times when it turns on normally, but if you turn it off and on again, the same defect appears (reduced frame, OSD repeated on the screen) | Diode 6199 bzx79-c5v6 on the side of the subwoofer | Check the bc548 next, and also the tip42c | ANDRE |