Philips Repair Tips

Search: philips
Results: 14208

Make	Model	Symptom	Problem	Solution	By
PHILIPS	21PT8467/78	Vertical closed with a horizontal stripe and turns off after 3sg	Resistor (3445) 1r open		letwister
PHILIPS	FW-C505	I'm sound	I had the 3.15 amp left output protection fuse burnt out. device.it only outputs sound on one channel if the good output is on the left side.in other words, on the ci7301, otherwise it does not output sound on one channel.	In short, I inverted the output from the 7302 to the 7301 and replaced the output that was on the 7301 with a new one because it was shorted from pin12 to pin11, in this specific case it cannot measure on this pin.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	FWC-507	I'm sound	Ci 7403 replacing pin 10 with 9 has the same function		eletronica alsat
PHILIPS	16GL1031	Green screen with retrace line	Após checar ic 997, ic900, s925, d365, d945, ts360, kt923, c921, ts943	I replaced the micro tmp47c434-r308 and the TV started working again	Marcio
PHILIPS	16GL1031	When turned on, the normal image appeared for about 3 seconds, then the screen turned green with a retrace line	Image tube replacement		Marcio
PHILIPS	21PT5433 L03LS1	No audio	Oops with changed data	Op1-000,op2-215,op3-001,op4-226,op5-082,op6-080 e op7-066	MAXWELL ELETRONICA
PHILIPS	DVP642K	Inoperative only on stand by	Q 301 short	Replace transistor	DEBIQUE
PHILIPS	14PT240S	Acting protection	Cold welding on vertical outlet	After resolving the same, the TV returned to normal	sergio
PHILIPS	29PT658A L01.1LAA	It turns off after a few minutes, sometimes it turns off as soon as it has just been turned on.	I changed q7461, and nothing, I changed c2455 with no improvement, I noticed that when the TV was off the air "without antenna", it didn't turn off, only when 10 minutes had passed and the message appeared on the screen that the TV would be turned off, if you change the channels without stopping it also wouldn't turn off, so I decided to make small adjustments to the 'vg2' screen, after a few attempts the TV stopped and turned off, returning to work normally.		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	20PT222A ANUBIS	Vertical closed at the bottom	Ic 7401 / c2463 / c2414 / c2443 / ic 7620	Replace the ci if it doesn't solve the problem, check the capacitors or eprom	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	21GX1666/789 ANUBIS	Blinking LED off	High power supply caused the device to block	Adjustment of the power supply through its module and connecting pins 1 and 20 of the ic7600 to unlock code ff, f8	rrsva
PHILIPS	29PT4635/78	When I turned on the TV it kept chirping constantly.	It's easy for the bu to burn out, I just changed it and it was stuck as a precaution, change the horizontal capacitors		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	29PT5642 /78 L04	Colored lines and does not open the vertical, then protects	Check d 6457 smd short		Master
PHILIPS	29PT5642	Vertical open open about 15cm with a sharp line right in the center and at the top and bottom of the opening it formed a sine wave with colored lines on both sides in red. green, blue.	Defective deflector detected on the bottom of the coil with I couldn't find it for sale, I opened it and I fixed the wire that was broken and the TV started working normally again.		Rivaldo Lira
PHILIPS	21PT6456	Screen closed without sound	Memory deconfigures	Configure or replace for another	EVALDO GOMES
PHILIPS	14PT418A/78R	Turning off and when held on and with green and yellow arrows in the image.	Kinescope	Changing the kinescope	ARISTEU
PHILIPS	20PT324A	Inoperative led off	Mp 08 / 116	Replacing it with the original serves as a fuse	EVALDO GOMES
PHILIPS	20GL1045	Vertical burned	Queima ic pos. 7410 (tda3653/bq)	Diode pos. 6565 (BYD33G) and POS1565 fuse (630mA)	jfmendes
PHILIPS	14PT3336	Intermittent on and off	Does not adjust the screen	R g b resistors replaced - I replaced them and solved the problem	OTECNICO.20M.COM
PHILIPS	29PT4640	It doesn't start horizontally, it only starts when you turn it off and when you turn it on at 110v	Pre-horizontal transistors, it is also ideal to check the 2 filter capacitors in this sector		Ronie Grein