Philips Repair Tips

Search: philips
Results: 14208

Make	Model	Symptom	Problem	Solution	By
PHILIPS	29PT552A/78 LLS	Burning1508dx	C2460 no driver horizontal		e.matos R.S
PHILIPS	20PT324A	Closing flashing image. When turning on the image comes back to normal after a few minutes on it starts to close the intermittent image, varying the width of the horizontal lines, sometimes also forming an intermittent and bright streak in the middle of the screen!	47uf/250v electrolytic capacitor 2409 near flyback		GEMASI
PHILIPS	21PT5433	Vertical, top of screen closed	Diodo 6460 / bas316	Replace the same; replace also cap.2463	eletronicaapolo
PHILIPS	14PT3131/78R ***	Turning off	Measuring all the smd transistors of the power supply, I released vertical, horizontal and sound output and the defect continued, then I released q7541 and q7551 and the TV in the same way. and I adjusted the vg2. the TV worked normally.	Loosen the transistors q7541 and q7551 to activate channel+ and adjust vg2.	wagner
PHILIPS	29GX1895/78R	Warming up horizontal outlet bu 1508dx	Cat made on top of the hot oscillator. n 7840 bd136	Replaced bd136 and bu1508dx	vicena
PHILIPS	20PT3331 LO3.1L AA	Doesn't start	Ic 7902=an7523 shorted, heats up printed on pin9 of the power supply switching transformer	Replace ic an7523	LOIMAR SILVEIRA
PHILIPS	DVP4000	Don't care, good power supply	Check if 5v arrives at c2709 and at the anode d 6617, if tsound is no 5v, check for a broken fillet near d 6617 between one side of the board and the other.		Bruske
PHILIPS	20PT3331 78R	Call whenever you want	Cold soldering on the micro, resoldering ok		J COSME, PARNARAMA
PHILIPS	20PT3331/78R HC840564	Vertical closed at the top and with lines (thank you very much)	Capacitor 4460 and also 7465		This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	14PT1353 L6.1	TV turned on with vertical closed, wire that goes to the deflection coil burned, due to the flyback arc, magnetized tube, due to the degausig coil terminals being broken, image blurred in cold weather.	Solder new vertical deflection wires, solder degaussing coil terminals, replace flyback.		geek1966
PHILIPS	21PT3131 L03.1LAA	Vertical	Partially closed at the top	Check. if the voltage at the collector of the 7464 below 20v: replace c2460 vert +b booster doubler.	tonintvtec
MINI SYSTEM PHILIPS	FWC 270 ***	When the mini system arrived at home I realized that tsound was no sound at 110v, I changed the sound output and it still had no sound, when I put it at 220v the sound appeared, I was intrigued and thought about changing the transformer.	Fet transistor p16ne06, when the current flows it trips and causes mute so I released it and the sound appeared, you can't do without it, it's output protection and I put the IRF 822 replacement in and it was fine.	Replace the transistor p16ne06 with irf 822 and that's it.	wagner
PHILIPS	DVD-625/781	When inserting the disc into the device, the display shows load flashing at a high frequency, and the disc does not spin.	Replace the disc drive motor, it's ok.		CLÁUDIO RIBEIRO, TECNOSAT ELETRÔNICA, JATAÍ-GO.
PHILIPS	20PT9467	Dead	Ci power supply and photo coupler		ELETRONICA ROBSON
PHILIPS.	29PT4631/78R	Black band on one side of the screen, approximately 5 to 7 cm wide.	Position capacitor 2486 disc=27pf by 2kv with leakage.	It was just a matter of changing and going out for a hug, it was….ok.	Armando da Eletrônica só Tv.
PHILIPS	14PT418A	Tsound's a plot, don't tune in.	R-3000, r3001 changed.
PHILIPS	FW M355/22	Without audio outputs on speakers, with audio on phones	Pa power supply (AN7830a pin 1) w/ 36v instead of 16.7	Mosfet transistor 7302 (which regulates the 16v7) in dc.	jose luis calcada
DVD PHILIPS	DVP3142	Engine doesn't turn, it's not the engine	Solution to change r76 on the mpg plate, very common in this model		fernando ferreira da silva
PHILIPS	14PT3131/78R PT3131	Green screen, with retrace and disarming	Resistor connected to transistor 7310 on the kinescope PCI (open/check)	Replace of the same	vinicius
PHILIPS	FW-M912	Does not turn on, tries to turn on, it seems that the relay does not arm or the relay keeps vibrating	Faulty relay t904		BRUSKE