Philips Repair Tips
Search: philips
Results: 14208
Results: 14208
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
14PT3336
|
It has a power supply but it oscillates and goes out | R 3445 open | miro eletronica | |
| PHILIPS |
FW-C505
|
No sound, exit ci ok | Ic 7501= tda7468d smd, pins 14 and 15 must have 4.8v if it is low check this clk and data line | BRUSKE | |
| PHILIPS |
20PT 3331/78
|
Vertical lines with interference at the top of the screen | Changed the c- 2460 68 k/ 100 volts | jaironuness | |
| PHILIPS |
29PT554A
L9 |
Image stretching to the left, tuning with low signal | The defect was because the power supply was low, I changed the position from the l5550 to the l5576, no power supply output, it was at 130v, I changed it to 140v, the TV was beautiful | Reversing the position of the l 5550 p l 5576 tv looks great | marcos melo[ CASCAVEL CE ] |
| PHILIPS |
20PT3331/78
|
Vertical closed | Changed the 10/250 volt c- 2465 | jaironuness | |
| PHILIPS |
20GL 1045
|
Luminance- obs: missing 180 voltsna r-3700 of 470 hms. | Trcar r-3550- 3,3 hms | jaironuness | |
| PHILIPS |
21PT1353/00
L 6.2 |
Difficulty tuning, no color and sound | Adjustable coils (5100) | Adjust but replace | J.CUNHA |
| PHILIPS |
14PT1352/00
L 6.1 |
Out of tune | Adjustable coils (5100) | Replace with new | J.CUNHA |
| PHILIPS |
29PT4641/78
|
Vertical only opens the bottom part of the screen. | Replace diodo ( d 6457 smd ) | dony eletronika | |
| PHILIPS |
14PT3005
L03.2L AA |
Upper line is protected. screen | C2460 devalued 0.068 | Replace c2460 r 3446 1 homs | ELECTROFRIO |
| PHILIPS |
14PT3005/44
L03.2L AA |
3 upper vertical stripes (r-b-g). screen | C 2460 0.068 | Replace c2460 | ELECTROFRIO |
| PHILIPS PLASMA |
42PF7320
|
Dead | Chap. c 8059 and c 8060 replace the two | DEBIQUE | |
| PHILIPS |
21PT5437/78
|
Dark screen with normal osd | Open resistor | R3442 120k was placed 100k | NELSON |
| PHILIPS |
21PT5437/78
|
Dark screen with normal osd | R3442 | NELSON | |
| PHILIPS |
21PT9467/78
*** |
Remote control and keyboards do not obey (message in the left corner of the factory screen) | Data loss | Ic-101 eepron 24c08 replace e pronto. | jose wagner |
| PHILIPS |
29PT5642
L04U AA |
When turning on stand by the power supply keeps pulsing and does not start horizontally. | Leaky coupler photo | antonio | |
| PHILIPS |
29PT4631
|
Turns on and off after a few seconds | Replace the two bc's 327 and 337 with bd135 and bd136 | And the note dies | AdrianChapadão |
| PHILIPS |
29PT5642
|
Don't care - | Photo opening 7513 direct replace | http://rmeletronica.com.br | |
| PHILIPS |
29PT4635
PV1913916 |
When the TV was turned on, the power supply kept pulsing but it didn't arm, | The bu 4508dx was burned out, I replaced it but the TV continued to have more problems, when turned on it turned off in 3 seconds. | I went to the extreme and found the defect was the electrolytic capacitor c2455 which is located close to two transistors which were also bad (7461-c337)-7463-c 327. Then the TV went fileeeeee | |
| PHILIPS |
21PT230
|
After turning on the TV, it returns to standby mode. | Electrolytic capacitor 2551.47mf/160v, without capacitance. | juares |