☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14210
Make Model Symptom Problem Solution By
PHILIPS 32PFL3404/78
Does not work/noise at power supply Capacitor cb1 with low capacitance or exhausted Replace cb1 - 4.7μF/450v ANTONIO DONIZETI DA CRUZ
PHILIPS 29PT552
The TV has no color and when you change channels it beeps and the horizontal output burns Defective memory because when changing channels it changes the horizontal frequency causing the bu1508 to burn I just replaced the memory and I'm fine charles cbs
TV PHILIPS 20PT424A/78R
L9-2A AA 		No sound, it doesn't amplify Dz 6953 3.3v and ci7953 pay close attention to the end of the sound ci letter, if it is mono it has to be tda7056b, do not put the end a cunha753
PHILIPS FW-380C
The CD doesn't work, it accepts selection for the CD but it is inoperative. Some key lights are off. Exchange of 7404, 7405 and 7406 hfe4094 smd on the panel joaomvjr
PHILIPS 21PT9467
Device after some time on, closes the vertical after about 1 hour Deflector opening one of the windings beneath the glue. It was very difficult to recover the deflector. I had to replace it. marcelo lurahy
PHILIPS 21PT5433/78
No, it doesn't oscillate. But if you measure the frequency, is it 15.7 kHz? R 3490 changed. Depending on the changed value, several defects will occur in the horizontal R3490 3k3 mecinhor7
PHILIPS 21PT9467C
I had already changed the band's integrated varicap micro memory, etc., a terrible defect only on channel 13, when it was cold, it was out of tune and then when it warmed up, the image improved, it was a more solved puzzle. And just remove the disk capacitor from the plate that is close to the 100k micro c828 Remove c828 from 100k disk carlos de maranguape1 paulista-p-e
PHILIPS 21PT6456
With sound without image R-3442 de 100k , proximo ao flay-back . Resistor aberto no pino 1 do flyback .... JOELTON
PHILIPS 14PT3132/78R
Has audio characters and a dark screen R3442 open abl line samuel leite
PHILIPS HPS-2991FS
TV burned out the bu 2520dx so far so good, so I bought another one I put it in its place but it didn't work it just oscillated but didn't produce high voltage, checking all the voltages which were ok after so much inspection I decided to put another one from an old board a bu 1508 then the TV worked Moral of the story, the bu I bought looked good but was bad internally, so here's a tip guys, be careful with your bu lol This email address is being protected from spambots. You need JavaScript enabled to view it. tecnico em governador valadares minas gerais 3330842033
PHILIPS TV PHILIPS GX 1899/78
No weapon power supply Exchange c 2420 c 2411 and c 2418 JCARLOSMART
PHILIPS 29PT558A
Without sound, but with image. Oxidized track or break near the seletronic ground, at the very beginning of the board. check the three trails. Bridge. lou
PHILIPS 29PT658
No sound, but normal image. Oxidized track or break near the seletronic ground, at the very beginning of the board. check the three trails. Make a bridge. lou
PHILIPS 29PT554A
Horizontal wind blower Resistor r3448 of 8k2 open. Ademir solânea pb
TV PHILIPS 14PT3131
Turns on the image appears but turns off in + or - 05 seconds Capacitor 2503 in the power supply primary Replace capacitor 2503, in the power supply primary. This capacitor was too small for its function. put a bigger one. caio
TV PHILIPS 14PT3131
Turning off in 5 seconds Replace capacitor 2503, in the power supply primary. This capacitor was too small for its function. put a bigger one. caio
PHILIPS FWM416X/78
Like fanhoso Exchange without measuring q721 fabiusmax
PHILIPS 32PFL3403/78
Does not turn on, only the standby LED is on. Eeprom memory (7l23) corrupted. leitemarcellus
PHILIPS 14GL1016
Philips tv 14gl1016 defect with normal sound on all channels + nothing appears. C2410 close to the top – vertical ONLY replacing the c2410 ginaldo silva casa do radio picui pb
PHILIPS 29PD860A/78R
A10 		When turned on, it goes into protection mode, activating transistor 7440 (prot-up), resistor 3437 open (22kohms) Replace resistor 3437 and check the others that are in series with it. leitemarcellus