☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14231
Make Model Symptom Problem Solution By
PHILIPS 29GX1895
ANUBIS 		Weak image, like bad tube R 3460 18k open ramiresrc
PHILIPS 14PT3131/78R
Inoperative (power supply changed at all power supplys) Ci7515 Replace the same Jarbas Santos (eletro-serv)
PHILIPS 21PT6456/78 - OU PT3336-PT3131-PT4131-PT3331-PT4331-PT5435
Enter service mode @@@ TV turned on with the remote control press the following keys in the sequence 062596 and the menu will appear on the screen the mode is used to make the adjustments and to finish press OSD and PAWER on the control ok your TV is programmed Help yourself, leave your tip ass.arni ELETRONICA ARNI-LEOBERTO LEAL-SC
PHILIPS 14GL 1314
High power supply (110v) I detected the fet transistor in short. I changed it and the power supply was changed I replaced the 3342 resistor (8k2) and the power supply returned to normal (70v) This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS 14PT3131
Inoperative power supply accumulating current. 3k3 1w resistor r9520 and the ic7520 tea1506t shorted. Replace ELETROCLAUDIO DE AGUAS BELAS PE
PHILIPS 21PT9467C
Vertical closed Check: r 09, 10, 318 - d 303, 304, 305 and vertical side. tyko
PHILIPS 21PT232A
L7PLUS 		Does not turn on, just stays on standby But b normal, but it didn't release the 8v, Smd ceramic capacitor c2422, with a cracked solder on one side, it was just a matter of re-soldering and the TV returned to normal. acms20
PHILIPS 21 GX 1666
ANUBIS 		Does not turn on, just stays on standby Keyboard locked Open or altered resistor r3561 next to the 13 volt power supply capacitor itan ( cabeça)
PHILIPS 20GX1658
ANUBIS 		Does not tune the channels, er 04 appears on the screen R 3452 of 47r open ramiresrc
PHILIPS 29PT4643/78
Turning off within a few seconds of switching on and perfect image giving error code 11 Broken kinescope Replace the kinescope samuel leite
PHILIPS 14PT4131
Dark screen Change 150k r3442 Evandro Estrela
PHILIPS 29PT552
Completely stopped (power supply zeroed) Capacitor c2550 in parallel with the secondary rectifier Replace c2550 (be very happy if you want you can deposit some cocoa in my account itan ( cabeça)
PHILIPS 29PT4631
L01.1L 		Lack of brightness or luminance Change the polyester capacitor that grounds the screen response to a TV without luminance This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS 29???
??? 		Nothing worked after closing Gecko jamming the keys Take out the lizard ODOBALDO PREGIDIO
PHILIPS 29PT 5642
Horizontal output is shorted C 2460 470/16 Leal
PHILIPS 21PT9467
Image disappears (turns dark) as it heats up Exchange q507 kinescope board NV ELETRONICA/VALDEMIR
PHILIPS 29PT4635
Overheating the horizontal transistor and it doesn't work Flyback Replace ELETROCLAUDIO DE AGUAS BELAS PE
PHILIPS 29PT552A
Does not oscillate C2551 not secondary fabiusmax
PHILIPS 14PT110A
Does not turn on, just stays on standby C2448 and c2551 of 47uf 160v Replace ELETROCLAUDIO DE AGUAS BELAS PE
PHILIPS 28PW6005/01
A10E 		There is no sound, no av, the sound level does not work No modulo bord 3139 123 5244.2 Non-ic solders 7301 (tda8885h) joaquim cunha