Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
29PT4631
LO1.1L |
Comes out of standby but doesn't work | Saida- horizontal | When power was activated, the LED would go out as if it were going to turn on and it would just not work. The defect was a short between the base and emitter of the bu4508dx horizontal output | GILSCE |
| PHILIPS |
21PT6456
L03LS1 |
Vertical closed at the top when it gets hot it opens | C 2465 10uf 160v | Replacelo | ANTONIO NOBREGA(PATOS PB) |
| PHILIPS |
29PT4635
|
Turns on, but cannot open the entire screen and with horizontal interference, returning to stand by. Many times it can't even be activated. | Change c2455 47x16v. | nachbar | |
| PHILIPS |
21PT5433
|
When turned on, it comes with a stripe on top and turns off - or turns on but has lines on top | Check bad cap very close vert c2465 10 p 100v outlet | COLOR TEC | |
| PHILIPS |
29PT6566
|
Doesn't start | Photo coupler 7513 with leakage | Replace | eletroclaudio aguas belas |
| PHILIPS |
FWM996
|
Only has sound from the subwoofer | 1k resistor near the cooler | MB ELETRONICA | |
| PHILIPS |
29PT9467S/78
SK5.0A |
Normal sound, filament off, no voltages on the screen and 180vts line with only 139vts | Flay back, practically dead, without generating high voltage | R406 1k/1w open, this resistor feeds the horizontal transformer (t401), just replace the resistor and it will work normally...... | |
| PHILIPS |
20PT3336
|
Power supply stays from 50 to 70v, TV does not oscillate, LED lights up normally and when giving power it spsgs normal, but of course horizontal does not oscillate. | See photocoupler | Replacement | Master Eletronica |
| PHILIPS |
29PT5642/78
LO4 LS1 |
Noise that increases when the brightness increases | Changed resistor r3606 from 39k to 27k | Carlos Lucio | |
| PHILIPS |
14PT3131
|
I'm here | TV full of undesirable insects (cockroaches, ants, etc.) | Carried out general internal cleaning/replacement of the open speaker | lpinheiro |
| PHILIPS |
20PT3331
|
No sound, or low sound | C2444 | guitec | |
| PHILIPS |
20PT122A/78R
|
Doesn't start | C2447 was leaking | Replace and run for the hug | serginhosond@yahoo |
| PHILIPS |
PT316
14PT316A |
Reduced frame at the top of the screen | Measure voltage scl and sda | dede som | |
| PHILIPS |
14PT1332/11
L6.1 |
Does not start, makes noise (wheezing), output on transistor "7504" 30v~ where it should be 96v | 330p 3kv "2501" capacitor in resistance, just change capacitor | jramalho | |
| PHILIPS |
21PT9467C/78
SK4.1L |
Retrace, white lines on the screen | R 3186,8 homs | Replace r 3186,8 homs | johnny busnadiego |
| PHILIPS |
HTS3152-55
|
Doesn't start | Plug it into the socket and the LED blinks and turns off, it remains without 3.3 and 1.8 | Replace the sa5888s servo motor | Lelo |
| PHILIPS |
14PT316A/78
|
Does not tune in, turns off in 10 seconds | C47 mf 160 v tda 7056b saida h bul312 fp | Replace them all | Nara |
| PHILIPS |
20PT3331/78R
|
Stand by LED lights up, presses channel, but does not turn on at all | Hand coupler | lord | |
| PHILIPS |
14PT133A
|
Does not tune in, turns off in 10 seconds | C47 mf 160v tda7056b saída h bul 312 fb | Replace | nara |
| PHILIPS |
29PT4635
|
Turning it off, several screen-adjusted components were checked and it didn't solve the problem. | It was only resolved with another tube | Replace for another good one | eletroclaudio aguas belas |