Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem
PHILIPS	25FL1760 FL1	Set tries to go to stereo as indicated by the on screen display, but most of the time it is stuck in mono, when in stereo the right channel was hissing	Replace the tda8415 on the stereo decoder board, confirm this buy putting multimeter on pin 7 and 8, they should have a voltage of 3.2 volts
PHILIPS	14PV184	Dead set / blown fuse	Replace d6313, 6314, 6315, 6316 and r3337 2r, 5w
PHILIPS	29FL1770 OR 25FL1760 FL1.0	After replacing the line output transformer, the following sympton was displayed. display flashing standby light and stereo ii	Short s23 and s24 briefly, which will put the set into service mode. option 1 should read 010 this applies only to the 25fl and 29fl. option 2 should be 001 for sets with text and 004 for sets without text
PHILIPS	21GR2751 G90B	Stereo set with no sound off air, maximum volume produces low hiss, some sound possible if station is detuned slightly. sound via scart is ok	Replace ic u2829b on audion panel
PHILIPS	14PV220 EPSILON 2001	Dead totally	Smps chopper ic 7310 mc44608 p75. i had no output from pin 5 with start up voltage pin 8 ok at 290v. if start up missing check start up resistor 3335 1k. the only power supply i found for ic 7310 was philips direct, part number 9322-143-51682, cost ~ £10
PHILIPS	VR6448 20921	Mechanism jammed, some posts hard to turn	Grease has turned into cement!! oil most of the moving parts, and move them to ensure oil penetrates
PHILIPS	33SL5796/16B FL 1.0	Snowy picture specially in vhf band. after about 5 minutes, picture snowy in all bands. about 10 minutes after switching on, no picture nor sound, just snow on the screen	Replaced the tuner/if. original code was fq816me which is no longer in production. replacement code is fq916dme
PHILIPS	VR678	Reel brakes not operating	Due to broken plastic pivot for pulse slider item 110 mounted on does not look like replacement part but wve stock holder, pulse mech kit pt no. 16256hl
PHILIPS	TURBO DECK	Chews tapes and poor tracking	Fit new pinch roller
PHILIPS	28PW6005 A10	Changes to ext 1 when watching tv ok with video input	Painter ic ic7064 failed on the ssb small signals board
PHILIPS	20PV164-05	Vertical frame collapse	Change vertical output drive ic and nearby electrolytic capacitor
PHILIPS	FL1.1AA	Int shutdown with lights flashing	Check the 18v zener d6376
PHILIPS	GR2.1 AA	Poor picture quality from cvbs ext1 and ext3. low intensity high saturation. loss of sync. shock and temp dependent	Dry joints on smd resistors 3014 and 3019 on if/sound module other side of encapsulated tda2549
PHILIPS	COMBI 14TVCR240	Poor tape transport, tape is crumpled, upper or lower side gets rippled	Replace the capstan roller, if the tape transport is still not smooth check the guidepole between the audio/control head and the capstan, tape must touch border-ring. adjust the audio head position screws marked a and t
PHILIPS	A10E	Randomly switching to scart input when the programme output from the tuner should be displayed	This is now becoming a common problem, the cause being the painter chip ic7064 which is located on the small signals panel, there are 8 different versions but only 3 common versions
PHILIPS	ANUBIS A-AC	Low 95v rail, 35v	C2530 open circuit completely
PHILIPS	L6.2	Power supply will not start up	Resistor 3506 0.33Ω, 1w fusible had failed, a replacement brought the set to life
PHILIPS	TX2112 U5N	Sound mutes for too long when changing stations up to 30 secs	The mab8441-t005 was faulty no longer available
PHILIPS	GR2.4AA GR2.4AA	No picture, just black screen	Check r3414, an smd chip on the crt board. there could be invisible bad solder joints
PHILIPS	32PW6526-05 SA10E	Procedure to exit child lock with pin unknown / "locked" displayed on screen	Switch set on, press menu, select feature and press enter, select parental lock and press enter, then enter the code 0, 7, 1, 1 twice, the lock should now have cleared