Philips Repair Tips
Search: philips
Results: 14245
Results: 14245
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL1.1
|
Alternative for a66eak252x43 | Alternative for a66eak252x43 ---------------------------- the following blackline s tube will no longer be supplied: 28" a66eak252x43 4822 131 20502 this has been replaced by: 28" a66eak252x44 4822 131 20567 remarks : if an old picture tube | ||
| PHILIPS |
FL1.1
|
After some time, no line sync. | On the high end box. check/replace ic7204 (pcf80c51bh-3p/j363; 4822 209 31386). | ||
| PHILIPS |
FL1.1
|
After some time, no line sync. | On the high end box. check/replace ic7204 (pcf80c51bh-3p/j363; 4822 209 31386). | ||
| PHILIPS |
FL1.1
|
After about 10 minutes: red or blue picture, flyback lines | Check d6450 on the ssp, at pin 19 of tda460 video controller ic (llz-c6v2; 4822 130 81512). | ||
| PHILIPS |
FL1.1
|
After about 10 minutes: red or blue picture, flyback lines | Check d6450 on the ssp, at pin 19 of tda460 video controller ic (llz-c6v2; 4822 130 81512). | ||
| PHILIPS |
FL1.1
|
After 10 minutes picture becomes red from right side | C2395 on the lsp poorly soldered. | ||
| PHILIPS |
FL1.1
|
50hz buzz noticable through speaker | Check/replace ic7680 on the ssp - tda8425, pseudo stereo ic. (4822 209 63734). | ||
| PHILIPS |
FL1.1
|
22av1440 is switched on by external vcr when fl1 is switched off | Connect 4 diodes of type bat 85 to inputs of ic7630 on ssp. 1 diode between pin 3/ic7630 and +5v, cathode to +5v. 1 diode between pin 5/ic7630 and +5v, cathode to +5v. 1 diode between pin 3/ic7630 and -8v, anode to -8v. 1 diode between pin 5/ic7630 and -8 | ||
| PHILIPS |
FL1.1
|
100hz cross | Possible solutions: 1. interrupt on the ssp the 50hz y-signal, between pin 11 position ic7324 (tda4568) and pin 11 position ic7395 (tda8443), by deleting position 4302. repair the connection by means of a shielded cable of 16cm long, m | ||
| PHILIPS |
FL1.0S
|
Wrong synchronization, unstable colors | D6417 on the lsp dependent on temperature, check/replace (4822 130 81223) | ||
| PHILIPS |
FL1.0S
|
Unstable picture, horizontal jitter. | Check/replace r3405 on the lsp. (4822 051 10303 for 50 hz sets; 4822 051 10333 for 100 hz sets). | ||
| PHILIPS |
FL1.0S
|
Tuning does not function | Resistor r3240 on lsp in v-tuning wire broken. | ||
| PHILIPS |
FL1.0S
|
Totally inoperative. | Transistors 7250 (bux85f; 4822 130 62509) and 7251 (bc848; 4822 130 61207) in microsops defective. or d6251 (llz-c5v6; 4822 130 80954) and r1250 (=r3230; 1Ω; 4822 052 10108) defective. or t7270 (bd825; 4822 130 41746) or t7201 (bc857c; 5322 130 427 | ||
| PHILIPS |
FL1.0S
|
Total inoperative, leds blinking, error 99 | Check and replace if necessary c2504 and/or 2505 (2kv hrr) on the large signal panel. replace by a 3kv15 hr-r capacitor if possible: 820pf 4822 126 13152 1nf 4822 126 13153 1,2nf 4822 126 13154 1,5nf 4822 126 13155 1,8nf 4822 126 13156 2, | ||
| PHILIPS |
FL1.0S
|
Ticking noise and line in picture | Transistor 7381 (bc848c; 5322 130 42136) defective when hot. | ||
| PHILIPS |
FL1.0S
|
Synchronization, picture disappears | D6703 and t7704 defective on picture tube panel. | ||
| PHILIPS |
FL1.0S
|
Switch-off spot visible longer than 5 seconds. | 1) change item c2518 on the lsp into 10uf 250v (4822 124 23494). 2) for 29" and 33". as service solution the eht cable can be replaced by 4822 218 21041. this eht cable with bleeder provides a faster discharge time. remarks : 1) so | ||
| PHILIPS |
FL1.0S
|
Spook in picture | Use special antenna cables. codenumbers: 4822 321 61224 pal 1 meter 4822 321 61225 pal 2 meter 4822 321 61226 secam 1 meter 4822 321 61227 secam 2 meter | ||
| PHILIPS |
FL1.0S
|
Spare part information alternative for a80ebk221x0 | Spare part information alternative for a80ebk221x03 --------------------------------------------------- the following picture tube will no longer be supplied: a80ebk221x03 4822 131 20376 this has been replaced by: a80ebk221x01 4822 131 20579 if an old | ||
| PHILIPS |
FL1.0S
|
Severe moire patterning | Most modern colour televisions use automatic gray scale tracking and while the setting of the g1 may not seem to have a major effect on the picture brightness on a modern set, incorrect adjustment can have the effect of causing severe moire patterning if |