☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14210
Make Model Symptom Problem Solution By
PHILIPS FL1.0
Set in stand-by mode, cannot be switched-on with remote control. Check diode d6522 (bdy228/20; 4822 130 41275) and transistor t7610 (bd948f; 4822 130 60935).
PHILIPS FL1.0
Set can only be operated with remote control Check whether "child lock" is disabled. to check this, see "frequently asked questions", "how to disable child lock".
PHILIPS FL1.0
Service manual corrections; remote control battery Service manual corrections; remote control battery lid ------------------------------------------------------ in the service (model) manual the battery lid (cover) for the rc6411 and rc6412 is supplied without the metal battery contact. code numbers for
PHILIPS FL1.0
Service manual correction ts7005, ts7006 Service manual correction ts7005, ts7006 ---------------------------------------- in chassis manuals for the fl1.0, fl1.1, fl1.6 and fl1.7aa transistors ts7005 (bc848c) and ts7006 (bc848c) in diagram g are drawn incorrectly. they should be drawn with coll
PHILIPS FL1.0
Sat box txt Sat box txt ----------- modification: item 3333 added 4822 116 52284 (47k) remark: mounted between pin 11 of ic7330 and l5350. reason: pull-up resistor needed for d2sync of the tpu (tpu error) production intro date: week 9234.
PHILIPS FL1.0
Production modification tda4680 supply Production modification tda4680 supply -------------------------------------- jumper 9481 is replaced with a diode type bat85 4822 130 31983 cathode to pin 5 of ic7430, tda4680 on the ssp. remarks : introduced production in week 9228.
PHILIPS FL1.0
Problems due to cnx83x Change into cny17-3.6 (4822 130 83177) remarks : production intro date: 92-06-18
PHILIPS FL1.0
Pip picture not in order. Check r3345 (4822 111 41424) in pip unit, check ic7755 (4822 209 63423).
PHILIPS FL1.0
Picture twists from top Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219)
PHILIPS FL1.0
Picture twists from top Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c5v6; 4822 130 80954).
PHILIPS FL1.0
Picture twists from top Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219)
PHILIPS FL1.0
Picture moved to the right Voltage of pin 12-ic7400 on the lsp has raised to 1 v (0,6v). check resistor r3408 (33k; 4822 051 10333).
PHILIPS FL1.0
Picture disappears (fly back lines), on stereo and dual leds blink Check ic7430 (tda4680). when tda4680 is too hot there is no picture (4822 209 31592).
PHILIPS FL1.0
Picture disappears Check voltage on tp55 on the lsp. if not correct, check c2528 (4822 121 40336)
PHILIPS FL1.0
Overview of sops repair kits Overview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.2 4822 310 31932 fl1.6
PHILIPS FL1.0
No stand-by mode In stand-by mode (+141v) is >> 0v. check d6352 and d6353 (ll4148; 4822 130 80446) on the lsp. note: on print lay-out (service printing), the anode and cathode in fl1.0 aa service manual are interchanged. the cathode has to be connected with pin 5 of the s
PHILIPS FL1.0
No sound, "on, standby, i" leds blinking 10mhz crystal 1602 on the ssp defective, 4822 242 80276
PHILIPS FL1.0
No red measure line when set is cold, after 2 minutes set is ok. Ic tda4680 on ssp defective (4822 209 31592)
PHILIPS FL1.0
No picture, sound ok. If burst-key signal is o.k.: check d6404 (ll4148; 4822 130 80446) on the ssp.
PHILIPS FL1.0
No picture, sound is ok. error 00 99 07 15 09. Check r3480 and r3481 on the ssp. (2,7Ω safety resistor; 4822 052 10278).