☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14245
Make Model Symptom Problem Solution By
PHILIPS FL1.0
Tuning does not function Resistor r3240 on lsp in v-tuning wire broken.
PHILIPS FL1.0
Totally inoperative. only red led on. Check line driver transformer l5503 on lsp (4822 142 40328).
PHILIPS FL1.0
Totally inoperative. Transistors 7250 (bux85f; 4822 130 62509) and 7251 (bc848; 4822 130 61207) in microsops defective. or d6251 (llz-c5v6; 4822 130 80954) and r1250 (=r3230; 1Ω; 4822 052 10108) defective. or t7270 (bd825; 4822 130 41746) or t7201 (bc857c; 5322 130 427
PHILIPS FL1.0
Totally inoperative, only standby led is on. Check t7610 (bd948f; 4822 130 60935) and d6522 (by228; 4822 130 41275) e/w circuit.
PHILIPS FL1.0
Total inoperative, leds blinking, error 99 Check and replace if necessary c2504 and/or 2505 (2kv hrr) on the large signal panel. replace by a 3kv15 hr-r capacitor if possible: 820pf 4822 126 13152 1nf 4822 126 13153 1,2nf 4822 126 13154 1,5nf 4822 126 13155 1,8nf 4822 126 13156 2,
PHILIPS FL1.0
Ticking noise and line in picture Transistor 7381 (bc848c; 5322 130 42136) defective when hot.
PHILIPS FL1.0
The +141 is about 110v instead of 141v It is recommended to replace the sops pwb for sets < ag04 codenumber is 4822 310 20492. for sets > or equal to ag04 codenumber is 4822 212 23748.
PHILIPS FL1.0
Synchronization, picture disappears D6703 and t7704 defective on picture tube panel.
PHILIPS FL1.0
Spook in picture Use special antenna cables. codenumbers: 4822 321 61224 pal 1 meter 4822 321 61225 pal 2 meter 4822 321 61226 secam 1 meter 4822 321 61227 secam 2 meter
PHILIPS FL1.0
Sound distortion. voltage pin 4 ic7635-2b too low. Check d6172 (llz-c7v5; 4822 130 80906) on the ssp for -8 supply voltage.
PHILIPS FL1.0
Sometimes set switched back to standby. only red led on. Microprocessor panel defective (4822 212 30502 and 4822 900 10331)
PHILIPS FL1.0
Sometimes no picture only sound. Check pin 3 from connector d14 (blue input).
PHILIPS FL1.0
Sometimes in protection, or hor. width varies Check or resolder on lsp the pins of e/w bridge coil 5521.
PHILIPS FL1.0
Set switches off by hardware protection from sound. error code 99. Check audio ic7000 on lsp (4822 209 73311; tda1521q).
PHILIPS FL1.0
Set shuts down. T7542 leaky.
PHILIPS FL1.0
Set in stand-by mode, cannot be switched-on with remote control. Check diode d6522 (bdy228/20; 4822 130 41275) and transistor t7610 (bd948f; 4822 130 60935).
PHILIPS FL1.0
Set can only be operated with remote control Check whether "child lock" is disabled. to check this, see "frequently asked questions", "how to disable child lock".
PHILIPS FL1.0
Service manual corrections; remote control battery Service manual corrections; remote control battery lid ------------------------------------------------------ in the service (model) manual the battery lid (cover) for the rc6411 and rc6412 is supplied without the metal battery contact. code numbers for
PHILIPS FL1.0
Service manual correction ts7005, ts7006 Service manual correction ts7005, ts7006 ---------------------------------------- in chassis manuals for the fl1.0, fl1.1, fl1.6 and fl1.7aa transistors ts7005 (bc848c) and ts7006 (bc848c) in diagram g are drawn incorrectly. they should be drawn with coll
PHILIPS FL1.0
Sat box txt Sat box txt ----------- modification: item 3333 added 4822 116 52284 (47k) remark: mounted between pin 11 of ic7330 and l5350. reason: pull-up resistor needed for d2sync of the tpu (tpu error) production intro date: week 9234.